Paddy's Ocean - 70 Gallon Mixed Reef **Phoenix Rebuild**

[michika]

Originally Posted by paddyob

I hope to have the same interest in the Phoenix.... as I hope to rise from the ashes.

If you build it....

Originally Posted by paddyob

I have had over 25,000 views of my build!!

I think you'll be good.

[paddyob]

Well here's what's left ...

FTS...



The remaining corals....

Photosynthetic Brush gorgonian (from Denny long back)
Purple Acanlord
Red Acanlord
Green Sinularia colony
4x RBTA
Florida Rics (shrunken but opening in 20g)

[gregzz4]

I'm kinda speechless ...

[paddyob]

Originally Posted by gregzz4

I'm kinda speechless ...

It's in full on crash mode. Bristle worms all over dead or dying. Water has gone milky. And stanks! I'll add a pic of that later.

I have turned off the lights and doser. I have a 38g I'm setting up downstairs for rock. I'm going to clean and re-cure it.

Disassemble and add some new things. Going to add a new breaker for dedicated line. Long over due. The stand I started will be in. Blah blah. There are a couple lights at the end of the tunnel and I will focus on fixing this and hopefully moving forward.

I'll start the maintenance work this weekend.

[gregzz4]

I know you're planning a Phoenix project, and I'll be looking for it

If I may suggest ...
Nows the time to go nuts, right ?
I ran 2 new circuits for my system, both with surge duplexes to protect everything. 1 circuit for the DT and 1 for the sump. I also built a big panel of GFCIs for individual hardware units, with each tied into my Reefkeeper PC4s
7 months and no problems with any of the hardware on either the surge or the individual GFCIs

[paddyob]

Originally Posted by gregzz4

I know you're planning a Phoenix project, and I'll be looking for it

If I may suggest ...
Nows the time to go nuts, right ?
I ran 2 new circuits for my system, both with surge duplexes to protect everything. 1 circuit for the DT and 1 for the sump. I also built a big panel of GFCIs for individual hardware units, with each tied into my Reefkeeper PC4s
7 months and no problems with any of the hardware on either the surge or the individual GFCIs

Could you post a pic. This is what I want to do. Switches to turn off pumps fit maintenance, etc.

I'm an not an electrician but my neighbor is. I'm hoping he can wire me up.

[gregzz4]

Originally Posted by paddyob

Could you post a pic. This is what I want to do. Switches to turn off pumps fit maintenance, etc.

I'm an not an electrician but my neighbor is. I'm hoping he can wire me up.

Sure, I'll post some stuff for ya
Having an electrician Pal is a big help, but I did this all on my own and I'm sure you can too

Definately nothing pretty, and I should have built a waterproof version
From my build, page 20, but there are other pages too

I didn't incorporate switches as I can turn off the GFCIs if needed, or unplug stuff, or turn off stuff in the Reefkeeper
Manually tripping the GFCIs may or may not shorten the life of the outlets, but it keeps me testing them



My PC4s (reefkeeper powerbars) are plugged in directly to the Surge Duplexes (hopefully protecting the circuitry), as are my Ground Probe and Utility Panel (bottom right section of pic - 4 duplexes)
I wired regular and heavy duty 'pigtail' plugs from the GFCIs, and they plug into the PC4s for control of the hardware

The relays you see (and there are 3 now) are just for 'run dry' and the ATOs are still functioning on their own. The floats on the relays protect the ATO powerhead and heater, and shut down the ATO pumps, in the event of a low water condition.

Feel free to PM me if you have any questions Pat, or other members for that matter

[paddyob]

Well I set up a 38g that has been in my garage for ages. An aqua clear and a heater. Rock tank. Going to clean all my rocks and cure them.