calling all electricans

[Skimmerking]

Originally Posted by Aquattro

3 MH and a big screen will trip the breaker. I know, i just had to run a separate circuit to my tank for this reason. Also take into account your heaters and pumps. You really can't run a tank your size on one circuit

ya that is what I was thing Brad. I will keep the
return pump ocean runnner 2500
ehiem 1260 skimmer pump
2x300 W heaters all n one circuit
and a 20 amp for the
3x250's
vortech
maxi flow
25 W night lite.
that should do it right and

thanks to you all for the help tonight

[Binare]

Dont do a gfci breaker, do a gfci receptacle instead.... Unless the plug will be behind your tank. That will save ya a hundred bucks or so. More so when it becomes weak and needs to be replaced. As a side note, yes ya can run a total of 12 devices off a 15amp circuit... Unless you know its intended purpose. Hopefully you put t-slot receptacles on your 20 amp circuit in your garage, your insurance company may give ya the boot if you ever have an issue out there.

[Buzz]

Originally Posted by Binare

Hopefully you put t-slot receptacles on your 20 amp circuit in your garage, your insurance company may give ya the boot if you ever have an issue out there.

Even if it passed inspection with out the t-slot receptacles?

[Binare]

Originally Posted by Buzz

Even if it passed inspection with out the t-slot receptacles?

I have alot to say about inspectors... Just not publicly ;-)

[raceit]

The thing to keep in mind is the purpose of the breaker, protection of the wire, not the device plugged into the outlet.

#14 = 15 amps
#12 = 20 amps
#10 = 30 amps
etc etc

max circuit load is 80 %

[Binare]

Originally Posted by raceit

The thing to keep in mind is the purpose of the breaker, protection of the wire, not the device plugged into the outlet.

#14 = 15 amps
#12 = 20 amps
#10 = 30 amps
etc etc

max circuit load is 80 %

yes and no. Depends on the duty rating of the breaker, whether the device is continious or non continious etc etc. . Hell some breakers dont trip at all. Federal Pioneer anyone? Dont worry, they finally fixed them hehe.

[raceit]

fp breakers are for welding, no stinger required lol

[2pts]

I'm not an electrician. I wired my own house (complete 200 amp service, 4500sqft).

I work with several electricians, and asked one "if you were gonna build a new house for yourself, what would you do that most premade houses don't have?"

His answer "I would install gfci outlets at the first outlet of each circuit". (If wired right it protects all remaining outlets on that circuit.)

So, I did that, the inspector said there was nothing wrong with the way I wired it, very safe, but I would have tonnes of "nuisance trips" from the outlets. Well I did, and promptly rewired almost all GFCI outlets so they only protected themselves, not the down line outlets.

I know it was overkill and expensive, but what I did was run 14/3 to my fishtank circuit, which is 2 seperate double plugs. (Be careful if you do this, research it a lot.) The white (neutral) is shared with the 2 hot circuits (red/black). In the panel I put in a double pole 15amp GFCI breaker ( $150 breaker).

I regret running the 14/3, that locked me into a 2 pole breaker, which is more money. If I did it again I would run either 2 lines of 14/2 and 2 single pole 15 amp gfci breakers or better yet 2 @ 12/2 lines and 2 single pole 20 amp gfci breakers. Reason being, if one circuit trips, it trips both breakers, meaning all my pumps die, except my return pump in the basement which runs in the sump and is plugged into a gfci plug on a whole other circuit.

[StirCrazy]

Originally Posted by 2pts

I know it was overkill and expensive, but what I did was run 14/3 to my fishtank circuit, which is 2 seperate double plugs. (Be careful if you do this, research it a lot.) The white (neutral) is shared with the 2 hot circuits (red/black). In the panel I put in a double pole 15amp GFCI breaker ( $150 breaker).

I regret running the 14/3, that locked me into a 2 pole breaker, which is more money. If I did it again I would run either 2 lines of 14/2 and 2 single pole 15 amp gfci breakers or better yet 2 @ 12/2 lines and 2 single pole 20 amp gfci breakers. Reason being, if one circuit trips, it trips both breakers, meaning all my pumps die, except my return pump in the basement which runs in the sump and is plugged into a gfci plug on a whole other circuit.

I was going to suggest running 12/3. I did this in my old house then used 15 amp breaker and 15 amp recepticles. I went for the 20 amp wire so if I found I needed the extra power later I could just change the breaker to 20 amp and the outlets also for cheep.

I don't know why you regretted doing it breakers are dirt cheep and you don't need a double pole. you can run two 15amp single slot breakers that way they will trip independently I have two circutes in this house that are run that way. 40 bucks in breakers (I have the expensive type in the new sub pannel ) if you have stablock you can get them for 10 to 15 bucks each.

Steve