|
|
|
#1
06-02-2010, 01:09 AM
|
|||||
|
|||||
Building a light rack
Anyone built one on here? I'm planning on of getting rid of my photon plus and building one to house a couple reflectors and a LED strip for actinics. What kind of material did you use and can it be done without having to weld? Im thinking about building it and encasing it in wood to match my stand to give it a floating hood look unless I can find a very attractive frame only design that would look good in my living room.
Cheers Ray
__________________
60" 120G project-DONE!!!! 
|
|
#2
06-02-2010, 01:53 AM
|
||||
|
||||
|
I'm planning on building one with three MH pendants and T5HO's supplimental lighting along with LED's for Moonlights on my new tank. Take a look at these guys www.eztube.com and you'll probably find something that will work for you.
__________________
Mark...  290g Peninsula Display, 425g total volume. Setup Jan 2013.
|
|
#4
06-02-2010, 02:20 AM
|
||||
|
||||
|
Quote:
|
|
#5
06-02-2010, 03:24 AM
|
|||||
|
|||||
|
HAHa I love mechano! Both those sites are great! makes things a lot easier. Do you know if there is a canadian company with a similar product? Id rather spend my money here instead of hand it to the americans lol
__________________
60" 120G project-DONE!!!!
|
|
#6
06-02-2010, 04:23 AM
|
|||||
|
|||||
|
I simply used square and angle aluminum stock from Princess Auto in Kelowna. Many big box building supply stores also carry aluminum stock, but I found the best deals & selection at PA. Stainless steel screws/bolts hold it together although in most cases I used a tap to thread the aluminum so nuts were not required. A few photos follow. I built two lumenarc reflectors from solar tube reflective material for my 250w MH and have two 4 foot T5s along the outer edge. There are an additional two empty sockets for T5s near the center, but I took them out after installing the MH. Bare bones, no fancy covering, but works for me. A future build will have it all hidden in a hood.
End shot, the large fans are no longer there, instead I installed smaller ones blowing directly on the end of each T5. The evaporation rate was crazy with those bigger fans running, good cooling for the summer though.  From the front. If I were to do it again, I might go with larger aluminum stock and run the wiring through the inside, but the bigger stuff gets pricey fast. The Workhorse ballasts for the T5 HOs are mounted at each end and blend in nicely with the overall aluminum look. Two hooks in the ceiling hold the plastic chain. This allows me to raise the assembly by hooking lower links in to the hooks. The lower assembly is attached with plastic covered steel wire and the MHs hang on separate plastic hooks. Excess plastic chain all over the place, but it allows for adjustments.  Close up of the new fan set up blowing on the T5 ends. The lamps are overdriven but the fans are doing a great job, no sign of blackening at the ends and I forgot when I installed the lamps. Still going strong. Also note the nylon screws I used to mount the various components.  Another close up of the fan mounting. I had to get creative with some scrap acrylic to mount them. 
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build  http://www.canreef.com/vbulletin/showthread.php?t=82206
|
|
#7
06-02-2010, 04:53 AM
|
|||||
|
|||||
|
Awesome there is a PA down the street from my work so ill go check it out. I am gonna be using lumenarc mini reflectors and a 48" reefbrite Led for supplementing and also moonlights. Did you make your rack the same footprint as your tank?
__________________
60" 120G project-DONE!!!!
|
|
#9
06-02-2010, 05:10 AM
|
|||||
|
|||||
|
Quote:
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206
Last edited by mike31154; 06-02-2010 at 05:12 AM.
|
Linear Mode
