Nate's "Oceanfront Bar" Mixed Reef Build!

NastayNatron · #1 10-10-2016, 06:02 PM

On to the sump! Things came together pretty nicely for such a small space. The reactor outlet enters back into the sump as a silicone line. I did this strictly so its easy to pull the line out and place it in a bucket while rinsing carbon/gfo. Enjoy!

NastayNatron · #2 10-10-2016, 06:10 PM

It's wet!

Time to finally get my rocks up into the tank! While researching aquascaping ideas, I came across one photo that I thought would fit my tank perfectly. I couldn't get the image out of my head so I decided to try and mimic it as best I could.

Inspiration:

Off to work! I used a hammer drill bit in a standard cordless drill to create holes where I needed them in the rock. Following that I inserted 3/8" acrylic rod into the holes. Some of the rock was epoxied, but a large amount was not. This way, if needed, I can easily lift a rock out of the tank off the acrylic rod.

NastayNatron · #3 10-10-2016, 06:14 PM

Once everything was rigged up outside of the tank, in they went!

Annnnd the completed product! I am happy with how it came out. I made sure to keep enough room between the glass and rock for adequate cleaning. Check it out!

NastayNatron · #4 10-10-2016, 06:20 PM

Might as well keep the posts rolling! Time for sand. I used CaribSea Aragonite Special Grade Reef Sand. It's the sand I have used in past tanks and I've always liked it, so why not.

RO Rinse! I did 5 rounds of rinsing and that cleaned it up nicely.

Into the tank!

warriorcookie · #5 10-10-2016, 06:29 PM

Looks great! Can't wait to see how this one turns out!

Make sure there's enough room between your rocks and glass for your algae magnet. One on the right looks like it could be too close.

NastayNatron · #6 10-10-2016, 07:05 PM

Quote:

Originally Posted by warriorcookie

Looks great! Can't wait to see how this one turns out!

Make sure there's enough room between your rocks and glass for your algae magnet. One on the right looks like it could be too close.

Thanks! I left enough room for the time being. I'm sure its going to be a battle once coral start to fill in to keep them away from the glass but that's a good thing haha.

Sorry about the massive pic drop! I felt like it was time to finally get a build thread on Canreef again!

FishyFishy! · #7 10-10-2016, 07:29 PM

Wow man. Thats some serious equipment and attention to detail! Looks amazing!

Where did you get the Cerebra from?

NastayNatron · #8 10-10-2016, 06:42 PM

After a bunch of back and forth, I decided to order the new Vertex Cerebra controller! I have it installed and wired in and will make sure to put an update on that all shortly. For now, check this beauty out! Bomb-proof packing as per all Vertex gear.

NastayNatron · #9 10-10-2016, 06:47 PM

And finally I hung my Radion XR-15pro G3 over the tank and transferred my fish and coral! I didn't have much of an ammonia cycle because I've had the live rock curing downstairs for so long. I also mounted my Vortech MP-10 on the back wall of the tank and it fit perfectly. My coral are all looking a lot smaller as I had byprosis in my small tank and did not plan on introducing it immediately in the new tank, therefore they were cut back a lot to prevent any carryover. The switch over went great and everyone is happy in their new home! My pistol shrimp and goby have claimed the underside of the large rock and are very active digging away as always! Check it out!

NastayNatron · #10 10-10-2016, 06:54 PM

Check out my sump! I decided to go with the Kessil H-150 Purple for my fuge light. I hung it with air craft cable and it looks pretty slick. It grows macro like crazy! Ill post a few shots of it lite up in the future.

All of the electrical runs behind the small drawer in the center of the stand across to the right hand cabinet. The electrical cabinet is about to get a big facelift once I get my dosers, new ATO reservoir, and a few other things, but its good enough for now.