Jamie's 13.3G Custom

yellowworld · #1 11-20-2013, 02:24 AM

This morning presented itself with a perfect oppertunity to get outside and not freeze! so here is the final product in all its tanky glory!

And here is my shop foreman!

yellowworld · #2 11-20-2013, 02:24 AM

I finally was able to the the finishing touches on the plumbing and got the tank fully setup and wet today!!! I still have the baffle the sump and get to Edmonton to pick up my new Apex, then get it installed and setup, then its on to the foam and rock wall!!!!!

yellowworld · #3 11-20-2013, 02:25 AM

Hey everyone so here is an update for you! I went and picked up some aluminum today to make a mount for all my controllers and switches, I modified the tracks that the original drawers for the filing cabinet were on to make a sliding pannel that will pull out of the cabinet to let me have access to everything on the panel, its not done yet. I still have to mout the last apex box and the netgear wnce2001 i just ordered to get it all online and then run all the wires and plug it all in but so far its looking good everything fits snug as a bug, and when its slid in i miss the return line by only a fraction of an inch haha weeeeoooo for measuring haha

But thats all for tonight folks, I have to run. I have a date with my gorgeous girlfriend!!

yellowworld · #4 11-20-2013, 02:26 AM

So i got a bunch of stuff done last night, and there is a lot more to come today and the next day. I got the rest of my electronics mounted and ready to be wired up, my apex is online now and waiting to be programmed

I also got my probes plumbed into my return line on the downside that will feed my fuge, i also finished that line as well too. believe it or not getting them to fit took me close to an hour and a half!!

today ill be finishing the baffling in the sump and then wiring the cabinet with a GFCI plug to run everything!!

yellowworld · #5 11-20-2013, 02:26 AM

Alright guys! today has been a good start so far, I got all the glass for the sump ready and siliconed in place

Then i got it put inside the cabinet and started putting my equipment in and sizing things up

1. Back right corner is the Tunze ATO

2. Right infront of the ATO chamber is the return pump, and to the right of the return and ATO is the fuge

3. Next came the skimmer

4. Then right at the front is the down pipes that feed the whole sump

5. the only thing left to do is to cut a piece of acrylic to sit just on the otherside of the tubes to hold my filter sock, then its water time!!

While i had the sump out i took the chance to wire in my GFCI plug and then cut up an extension cord to wire the whole box to one single plug that i can plug into an existing outlet under my desk

yellowworld · #6 11-20-2013, 02:27 AM

Hey everyone, time for an update!! over the last day or so i have been slowly turning this

into this!!

I still have a ton more work to do on it to make it look perfect and fit the same way, i also need to try out a few things to make the foam look identical to the rocks then epoxy it all and cover it in sand but its getting there!

ohh and yesterday this showed up in the mail! its 10 feet of 3/4 inch braided cable wrap! now i can clean up my wiring and make it look pretty too!!

All clean!!

yellowworld · #7 11-20-2013, 02:28 AM

So for all of you guys out there that just cant resist seeing what the rock wall is turning out like, here is a little sneak peak!!

okay so i took more then a few haha but i should be getting epoxy and sand on it in the next week and then ill let it sit in a bucket of saltwater for a week or so to make sure that all the dust is off the rock and that the epoxy did its job, then its on the Light and water!!!