Cloudy Water Ideas

[ruslicus]

So day 2:

NO3 <0.25ppm RedSea Test
PO3 0.08 Red Sea Test and 0.08 Milwakee test
Ca 423ppm Hanna Test
Alk 8.7 Hanna Test
PH 7.8 Digital Milwakee Test (mrning)

As I can judge I have close to 0 NO3 but elevated PO3, which means my NO3 export is overkilling but PO3 stil persist. The water is better but still not crystl lear as used to be.
I m going to turn on GFO and change the media GFO and Carbon.
Still waiting for water test result from Denny to cross check. The plan is to chek all these measurements daily over a week and see dynamic.

Target to lower Alk to 8 and keep Ca at 420-450, To control PO3 nd PH within 7.8-8.2

My issue is SPS coloration and STN or RTN.

Any feedback and comments how to solve the issue? Thx

[kien]

Originally Posted by ruslicus

So day 2:

NO3 <0.25ppm RedSea Test
PO3 0.08 Red Sea Test and 0.08 Milwakee test
Ca 423ppm Hanna Test
Alk 8.7 Hanna Test
PH 7.8 Digital Milwakee Test (mrning)

As I can judge I have close to 0 NO3 but elevated PO3, which means my NO3 export is overkilling but PO3 stil persist. The water is better but still not crystl lear as used to be.
I m going to turn on GFO and change the media GFO and Carbon.
Still waiting for water test result from Denny to cross check. The plan is to chek all these measurements daily over a week and see dynamic.

Target to lower Alk to 8 and keep Ca at 420-450, To control PO3 nd PH within 7.8-8.2

My issue is SPS coloration and STN or RTN.

Any feedback and comments how to solve the issue? Thx

Your numbers across the board are actually looking pretty good today. NO3 and P04 while not absolutely zero are still not numbers that I would panic about. Looks like alk is on its way down and again, 8.7 is nothing to panic about. CA at 423 is perfect and pH at 7.8 this morning is fine too. My pH is sitting at 7.8 now and will continue to climb throughout the day until it tops out at about 8.3 sometimes 8.4 before it starts to drop again for the night. My recommendation there is to not fight your pH. Let it do what it's going to do.

Your BioPellets should continue to drop your nitrates and bringing GFO back online will drop your PO4 to zero in short order.

[ruslicus]

I ust changed GFO media and Carbon media. will text PO3 from output of reactor in an hour to see if the reactor actually is working. I use 1cup of HG GFO, is it enough for 85-90gal water system? My concern isn't NO3 too low? talking about starving? should I dose some coral energy solution? but PO3 is too high... dilema!

[ruslicus]

So my PH range during the day was 7.8 to 8.1. which I think is ok. My issue is even after change of GFO and checking the outlet from GFO rector I still get 0.04-0.08 PO3? any ideas how I get PO lowered? GFO doesn't look like working?

[ruslicus]

Denny from Concept got back to me with following results:

alk : 8.53 vs mine 8.7
phos : 0.03 vs mine 0.08
nitrates : 0 vs mine <0.25
amonia: 0
calcium : 375 vs mine 430

My biggest concern Caclium and PO3 are big difference. What is the most accurate Test kit for PO3 and Calcium? Still my SPS are upset so should be a problem somewhere. Ideas?

[ruslicus]

So water is crystal clear now, which is good. But big issue cannot drop PO3, at least based on Red Sea test kit. My numbers today:
1. Salinity 1.025
2. PO3 0.08
3. NO3 based on test kit it is negative can it be a problem for SPS coloration?
4. Ca 450
5. Alk 8.6
6. PH 7.9-8.2 during the day

My pocci still not puffy yet.

[kien]

Originally Posted by ruslicus

So water is crystal clear now, which is good. But big issue cannot drop PO3, at least based on Red Sea test kit. My numbers today:
1. Salinity 1.025
2. PO3 0.08
3. NO3 based on test kit it is negative can it be a problem for SPS coloration?
4. Ca 450
5. Alk 8.6
6. PH 7.9-8.2 during the day

My pocci still not puffy yet.

Good to hear about the water. That's progress. All other values look reasonable. Phosphates should continue to drop over the course of the week if you have just installed new GFO. Test again on the weekend to see where it's at. 0.08 is nothing to panic about though :-)

Pocci (and other corals) may take much longer to recover from whatever shocked them. Could be the cloudy water, could be the paramter swings. Who knows, but whatever it was, their recovery may be a long slow road no matter what course correction you do now.