Woodwork helper wanted (Langley/Surrey area)

[duncangweller]

Hi all,

I am re-skin-ing my stand prior to moving house and am going to make it ADA style. Seeing as I have no tools other than a screwdriver, a spanner and a hand saw, Im not particularly equipped for cutting giant sheets of MDF.

Is there someone local with perhaps at least a circular saw who could help me cut some panels? My experience with the friendly people at home depot and their wonky cuts hasn't been to great and I news dead straight lines. I would be happy to chuck in a couple of tinnies as compensation.

Thanks all,
Dunc



Sent from my HTC Incredible S using Tapatalk 2

[monocus]

i would stay away from mdf.any water gets in the sides and it swells and disintegrates.if your ever in the burnaby area i can help you with cuts etc.

[frd72]

It is easy to cut mdf. if you want you can borrow my circular saw??

Originally Posted by duncangweller

Hi all,

I am re-skin-ing my stand prior to moving house and am going to make it ADA style. Seeing as I have no tools other than a screwdriver, a spanner and a hand saw, Im not particularly equipped for cutting giant sheets of MDF.

Is there someone local with perhaps at least a circular saw who could help me cut some panels? My experience with the friendly people at home depot and their wonky cuts hasn't been to great and I news dead straight lines. I would be happy to chuck in a couple of tinnies as compensation.

Thanks all,
Dunc



Sent from my HTC Incredible S using Tapatalk 2

[ckmullin]

Seal the MDF...that is key. before you throw it together seal the edges...throw it all together and seal all surface area in + out.

[Evilweevil]

Don't use mdf it's a sponge, sealed or not sealed use medex it's basically mdf with better glues and different additives to make it water resistant places like Windsor plywood would have this and are able to do a cut list for you ,I would think better then Home Depot also ( maybe)

[ckmullin]

Someone can use mdf as I've used it more than once. While it isn't my FIRST choice...someone can use it, as said key is to seal. It's also a skin, not structure.

[Evilweevil]

For relatively the same cost you can get a product that is made to be more water resistant so why wouldnt you ?being a finishing carpenter I wouldn't use mdf myself as I see sealed mdf swelling and falling apart all the time with very little water exposure , but yes you could use it

[ckmullin]

It wasn't the point of what is the best the OP of this topic asked about mdf not another product. I've been around wood for a number of years too and know in's and out's.

[Evilweevil]

Yes I am sure you work with word and that you are very handy with it

[whatcaneyedo]

Originally Posted by duncangweller

Hi all,

I am re-skin-ing my stand prior to moving house and am going to make it ADA style. Seeing as I have no tools other than a screwdriver, a spanner and a hand saw, Im not particularly equipped for cutting giant sheets of MDF.

Is there someone local with perhaps at least a circular saw who could help me cut some panels? My experience with the friendly people at home depot and their wonky cuts hasn't been to great and I news dead straight lines. I would be happy to chuck in a couple of tinnies as compensation.

Thanks all,
Dunc



Sent from my HTC Incredible S using Tapatalk 2

Doesn't your Home Depot have a large stationary panel saw like ours? Unless the saw is out of alignment or loose on its guides it should be able to make straighter cuts than some weekend warrior with a circular saw. Even the folks at a Windsor Plywood should be able to do a better job on their table saw. I haven't done much finish carpentry during my apprenticeship but when I have I put the circular saw away and set up the compound mitre and table.

I agree about the use of MDF as being a poor choice for use in a wet environment as well. If you're concerned about the appearance and longevity of your finished product why not spend a little more for a higher quality and more durable material like plywood?