Radions...ready to throw out the window

[Coralgurl]

Originally Posted by Nano

I say toss em and get SOLs jk

Nope, not going to debate lights, just a bit frustrated...

[mexxedm]

1. Unplug the power. Important step.
2. Plug in USB to computer.
3. Reset it.
4. Reprogram or use natural mode.
5. Set the time.
6. Program it.
7. Unplug USB.
8. Wait for 3 mins.
9. Plug the power in.
10. Try it again.
Mine went dead. Yes, completely dead. These steps worked for me.

[reefgirl189]

I had the same problem. Turns out that after programming you need to switch modes. Press and hold the cycle button (middle button). This will switch modes for you and you should hopefully find that it switches from pre programmed modes to your new finely tuned one. Hope that makes sense.

[Coralgurl]

I emailed ecotech and they said the same thing, I just haven't had a chance to try this yet. Hopefully that's all it is.

[Coralgurl]

We were out of town this weekend, I got home and noticed my radions are clicking and flashing. So I think something is off with the programming.

First issue, start program, plug in light, show it's connected but the other 2 aren't. So, refresh device list, it finds them good to go. Reset programming, lights start clicking again, and the 2 lights are now disconnected again.

Next issue, I disconnect the USB, unplug all 3 lights, plug back in and my left light will not turn on. So I unplug at the base, plug all back in. Lights on base all show green, but the LEDs stay off.

Restart program, plug in, it shows the lights are all connected, but I the left light will not come on.

Any ideas?

[SeaHorse_Fanatic]

Sounds you got a lemon. Maybe check with Ecotech about getting them replaced?

[Smudge]

Is the fan working on the one that won't light?

[Coralgurl]

Fans are running on all 3. They are dusty, will pull them all down tomorrow and clean.

I've sent an email to ecotech as well.

[Rice Reef]

Originally Posted by Coralgurl

We were out of town this weekend, I got home and noticed my radions are clicking and flashing. So I think something is off with the programming.

First issue, start program, plug in light, show it's connected but the other 2 aren't. So, refresh device list, it finds them good to go. Reset programming, lights start clicking again, and the 2 lights are now disconnected again.

Next issue, I disconnect the USB, unplug all 3 lights, plug back in and my left light will not turn on. So I unplug at the base, plug all back in. Lights on base all show green, but the LEDs stay off.

Restart program, plug in, it shows the lights are all connected, but I the left light will not come on.

Any ideas?

Check the fan ans see if it is running. A few mths ago 1 of my lights was flashing, checked it out and the fan was not running. I had contacted Ecotech and they told me there has been quit a few issues with the fan stopping and causing the lights to flash. It needs to be replaced if that is the case... Contact the store you purchased from and also the distributor for that store. Ecotech will not replace it for you as it has to be replaced by the Cdn distributor. I had posted this issue a few months back Unser equip. , lights.

I know what you are going thru as I've been there... Good luck.

[Coralgurl]

Originally Posted by Rice Reef

Check the fan ans see if it is running. A few mths ago 1 of my lights was flashing, checked it out and the fan was not running. I had contacted Ecotech and they told me there has been quit a few issues with the fan stopping and causing the lights to flash. It needs to be replaced if that is the case... Contact the store you purchased from and also the distributor for that store. Ecotech will not replace it for you as it has to be replaced by the Cdn distributor. I had posted this issue a few months back Unser equip. , lights.

I know what you are going thru as I've been there... Good luck.

I read through your thread. The fans on mine are still going but not as strong. Hopefully ecotech responds tomorrow.