biopellet flow

htfn · #1 03-12-2011, 07:30 AM

OK so maxi-jet 1200 is not enough flow. I guess I searched wrong place then. Do you think flow rate should be more than 350g/hr?

Bblinks · #2 03-12-2011, 07:46 AM

Quote:

Originally Posted by htfn

OK so maxi-jet 1200 is not enough flow. I guess I searched wrong place then. Do you think flow rate should be more than 350g/hr?

I honestly don't think you need anymore than that. The problem I had with TLF is the inlet and outlet, TLF comes with 1/2 inch barb hose but for pellets you need 5/8 or even 3/4 barbs so you can get the flow that you need without grenade the reactor. If I were you I would really look into a smr1 or a vertex reactor. If thats not an option, try to find some thing used. All else fails, throw a bigger pump on it and make sure you remove the foam in the TLF, re-tap the barb fitting so you can put a larger diameter hose an try again. Be patient and let I run for awhile. I have had very good results with running the pellets. The smr1 with the pump costed me around less than 200 with tax.

htfn · #3 03-12-2011, 08:39 AM

Yes I already remve foam and install mod both bottom and upper plate, but I did not know I have a reactor problem. What you pay, what you get, right? I will serch the other reactor or try to put a larger hose.
Thanks

reefan · #4 03-12-2011, 03:41 PM

I use the large Vertex reactor and it works fine, no clumping.

The Grizz · #5 03-12-2011, 05:55 PM

The NextReef MR1 has 1/2" barbs and works great.

Bblinks · #6 03-12-2011, 06:09 PM

Quote:

Originally Posted by The Grizz

The NextReef MR1 has 1/2" barbs and works great.

The MR1 has 1/2" barbs that is correct. I did mod my MR1 to run pellets as well. It does work great but it's not until I switched to a SMR1 I noticed a big flow difference. Of course I ran it with the same pump, it just seems to have less pressure built up inside the actual chamber rather than flowing through it. Don't get me wrong, when I was running the modded MR1 it worked just fine.

globaldesigns · #7 03-13-2011, 03:28 AM

FYI, I use a maxijet 1200 with a Vertex15 Reactor. Works perfectly for me.

I don't use any foam in the reactor, as they will just get gummed up with tank gunk and pellet mulm.

jonnyjamms · #8 03-14-2011, 06:06 PM

I set about 3 weeks ago, I have not seen any change. I heard that over the short term should cyano. I also use copper and aluminium composite reactor and the maximum 150 jet 1200. I saw the ball was dropped, but more likely at the bottom of the upper is still rolling, but I do not think it is positive. What am I doing wrong? Would be grateful, if someone can solve my problem.

asylumdown · #9 03-15-2011, 12:09 AM

Is it true that most people see a cyano flare up when these things get turned on? I've had mine on for... I guess over a month now and my cyano problem has gotten a little worse. I'm seeing less algae growth for sure, but it's almost like the cyano is just picking up where the algae left off.

Bblinks · #10 03-15-2011, 12:47 AM

Quote:

Originally Posted by asylumdown

Is it true that most people see a cyano flare up when these things get turned on? I've had mine on for... I guess over a month now and my cyano problem has gotten a little worse. I'm seeing less algae growth for sure, but it's almost like the cyano is just picking up where the algae left off.

Every one that I talked to have had cyano problems around 2-4 weeks into the initial start, I myself had the same problem. Bacteria boom is probably the cause of it. Just be patient and let it run its course. If you still having the same problem in a few month than you need to go over the flow rate and or the where the water is being discharged. Make sure water is being dischaged in front of the skimmer and frequent phosphate test to ensure the level is slowing decreasing. I suggest the hanna low range test kits as they are the most accurate test out there. imo.