Asmodeus's 8 footer New pictures for Lance

[SmallFry]

Originally Posted by Skimmer King

Well an update of the stand went to home depot to get a price on the cabinets and OMFG. $7600 for the cabinets around the tank. looks like that i'm going another route for the cabinets tank on hold til i can figure this one out . sorry folks. I have them looking for a less price in the 15-2000 range..

That is insane - was that for just the doors or cabinets too? Have you tried some of other builders merchants in town? Most of them do kitchen stuff too, and I've never seen a house we built get a kitchen, or pretty much anything else for that matter, from home depot. Maybe their consumer friendliness comes at a price?

There has to be a way of doing it cheaper if that fails. You/we could make doors cheaper if we went for something like a plywood door with a wood trim around the edge (and you could have your custom sizes that way too).. Would be more of the Ikea type look, but you could make it 'pop' a bit with a different colour of wood for the trim; something like that computer table I have if you remember it. Bubinga (expensive) or Mahogany (less so) would stand out nicely if you're going for a light wood for the main part - and you can stand the pink dust when you sand it...

A suggested already, Ikea itself may also be a viable option even if you have to go and get it - I don't remember their stuff being that expensive and I have a soft spot for Ikea. Would be well worth a look at their website. It's also worth noting that the American Ikea seems from the websites to have a better range of stuff than the Canadian one. Don't know where the nearest American store is though. I think the nearest Canadian one is Calgary until they build that one in Winnipeg...

Finally, there's a Hutterite colony somewhere that does kitchen cabinets, I'll see if I can do some finding out...

Rob.

[Skimmerking]

Well I start building the cabinets with my Carpenter friend tomorrow YAAAAAAAAAAAAAAAAAAAAAAAAAAAAA,. Im going to be going with Maple and I will be building the doors too.

But got bored and was levelling the tank and so i started to fill some of the tnak with some make up water that I. I needed to flush out the membrane "ya that is it flush the membrane out".

so did some zap tying the rocks on the other side not bad I guess.

Not much to look at sorry folks

Here is the right side of the tank .

[Skimmerking]

Ok so I bought the Wood for the stand I'm going to be going with Birch. Thought that i would try something different. Got together with my buddy who is allowing me to use his shop. Came up with a plan and a drawing He would let me use the shop unless I had a vision in my head and something on paper. He knows me to good. The Stand will have access through the front however I will be using Rare earth magnets to hold the front on plus to latches for safety. I'm going to be having a feed door on the left side so im not always in the top Hmmmmmmmmmm like that is going to stop me. The stand will 78" high and then 4" piece of crown molding shelf lick will be on the top.

I'm hoping to have this stand done by end of the month. The Reason I placed my order for 5 Small yellow tangs, 1 chevron tang, and a Tommi Tang. So I want to have them in the tank before I add (LIPS AKA sailfin)
and (@ss AKA KOLE) and well LULU she just don't care and man she is getting fat close to 1.5" fat and 5"

I'm going to paint the inside of the hood white with bathroom to seal it. and its going to be stained on the outside just haven't figured out what.

Well I will have build pictures tomorrow

[Skimmerking]

Well Yaaaaaaaayyyyyyy I got some progress done on the stand well Cabinets. tried to take some pictures of as myself and Dwayne a good friend of mine as we were working. So I hope these are good enough. So far I bought 6 sheets of 4x8 Birch and end roll to mask the ends of Birch. I'm still having the dilemma of the canopy since the top is going to be huge 8 feet long I'm going to run 1.5" strips all the way down underneath the top of the cabinet to stop it from bowing. the doors will be 2x48 so its alot easier to take off that attach to the Magnets. " SO HOW ABOUT I SHUT UP AND SHOW YOU THE PROGRESS....



here is the wood sitting here. mmmmmmmmmmmmmmm WOOD!!!!


Some of the corners sorry forgot to take some build pic's of the tower oooops


and some more



This is the inside of the right tower where i will need to seal with a White Bathroom paint for high humidity. See I'm a thinking ahead already....

ME SMRT SMART


TAAAAAAAAAAAAAAAAA DAHHHHHHHHHHHHHHHHHHHHHHHHHHHh
The right Cabinet where all the equipment will be. like the
Sump. Skimmer, Kalk Reactor. you get the drift.


Well for Poon Tang here ya go man..

ACTION SHOT.

Is it real yup taste like BIRCH.



Now on to the Front, to SKIN OR NOT TO SKIN, THAT IS THE QUESTION!!!!!!!.




what biscuit TIME OMG
HEY JUST WAIT A FRIGGIN MINUTE HERE THIS AIN'T NO BISCUIT WHAT THE HECK!!!!!!!!!!

[hillegom]

comming along nicely.
I didn't know you could straighten out wood with the iron! Interesting.

[Skimmerking]

TIME TO HEAT THIS BAD BOY UP.....


SOME FINE TUNING AND A HAPPY HELPER.

i'M TRYING TO CONVERT HIM TO salt water, he was big in to fish in the past.









This I got to thinking About a shelf for the Deltec 702, Hmmmmmmmmmm

Well watch this.
MEASURE 10 times


ok one pic's for LAST LIGHT since he is so SWELL.

A Little bit of this and that...

Not Bad eh!!!!!!!!!!!!!!!!!!!!!!!!!

[lastlight]

Dude that is so softcore. There's no real contact happening wth?

Other than that I'm liking what I see. My canopy is just going to be a 2x4 framework above my tank but tied into my joists. Then I'll worry about skinning it. Not sure you can get away with something that crude or not.

[Skimmerking]

This is the 2 cabinets that were made.. Im going to have 1 complete door for the small one 78"x15" and 2 doors for the right cabinet 78"x36" and I will put a kick plate on them too

[Skimmerking]

Brett this Photo is me bringing Sexy BACK

[lastlight]

Originally Posted by Skimmer King

Brett this Photo is me bringing Sexy BACK

Back to what... remains to be decided =)