|
|
|
|
|
#1
12-19-2010, 12:43 AM
|
|||||
|
|||||
No new pictures yet but lots of change.. heh
got bored today.. .. drilled an old 20g i had around.. bought some plumbing... played around not what i intend to do, but.. now i got a 20g.. with a 250wmh and the mp10.. with a little rock, and most of my sps frags that have been dragging along.. plumed into the 40 that i put all the old korrilas back into. so 20g sps tank.. hopefully the sps will do better with even more flow and don't get to shocked from change in light. none of the big crabs or other coral harasses got moved into the 20. my 14g cube is still running but is now back in the dark, it was starting to look good with that 250 running on it the last few weeks but it will be maintained as a q-tank for now, pulled the few corals i had out and the one crab and snail i could see so it can stay that way till its needed. I still need to suck a bit more black-nasty sand out of the 40 but i need more water for changes i guess i should have got the bigger brute than i got heh. if everyone opens back up ill take some pics. 
|
|
#2
02-18-2011, 09:36 PM
|
|||||
|
|||||
|
Egad's I am bad with the pics and posts lately, perhaps because I am unhappy with the tank.
got a couple new fish and corals over the holiday sales, everyone made it and is settled in. still having problems with my sps but they are growing and coloring up. haven't tested MG in forever because one of the vials was missing, finally found it today and.. .. wow.. I think thats why my sps are not growing. I was adding some liquid MG once a week or so without testing <but probably not enough> and it ran out a week or 2 ago. and i kept forgetting to buy some when i was at any store.. heh.. off to the stores i go mg of 5-600 doesn't grow corals well from what i hear.
|
|
#3
02-18-2011, 09:43 PM
|
|||||
|
|||||
|
OoO the other misadventure of the tank.
while looking at how to set up some temporary extra circuits for my tank until i move or the basement is finished realizing that 1 of the 2 circuits the tank is plugged into already is an Against code added in plug off the feed for the furnace. but really its ok to have near maximum rated draw going to your tanks and hope everything works out every time the furnace turns on.
|
|
#4
03-05-2011, 10:40 PM
|
|||||
|
|||||
|
something missing from my basement today...
and i like it the sound of this system roaring and gurgling away is all gone. curently picking little bits of life out of the sand before i get rid of it. everything has been crammed into my 50g and looks a lot better in there. I was going to tweak this thing out to be quiet while everything is in the other tank but i think i will just get rid of everything and save up for the next big thing.
|
|
#5
03-05-2011, 11:15 PM
|
|||||
|
|||||
|
Oh the decisions.. the old stand fits right behind the new tank.. and the 50g sump even has a hole predrilled near the top when i wanted to make it a refugieum to my old sump..
50g refugieum should have enough pods to keep a tank full forever eh? good thing i have to drain it to move it up there gives me an hour to think about it.
|
|
#6
03-09-2011, 04:40 AM
|
|||||
|
|||||
|
Just when i thought i was ready to go to bed...
barely touched the tank and got a full 120 zap... mmM fun.. grabbed my greeny potential tester, that can usually just pick out the hot wire in a 2 conductor wire and my whole tank lights it up.. oh well start unplugging things i guess
|
|
#7
03-09-2011, 05:14 AM
|
|||||
|
|||||
|
somehow the cord for a powerhead got a nic in it and that was underwater... ugh. at least now i can sleep.
the tank still has 24-28 volts induced voltage from everything else. one question for the electrically inclined. if you are running off multiple GFCI should your ground probe tie to all the gfci's?
|
Hybrid Mode
