DYI Standpipe

[Lampshade]

A cheater way is to not use a bulkhead.... if you get a male threaded 1.5" PVC fitting, a flemale one and a soft O-Ring you can make a bulkhead out of it pretty easy. Cut the female threaded fitting off to use it as a tightening nut, and now you have a 1.5" PVC fitting in a 1.5" hole. 1.5" can flow 1200+GPH pretty easy, I was getting 1200+ on mine when it was duroso, now much more as herbie. Specs say 1600GPH, with gravity feed.

[Magma]

Originally Posted by Lampshade

A cheater way is to not use a bulkhead.... if you get a male threaded 1.5" PVC fitting, a flemale one and a soft O-Ring you can make a bulkhead out of it pretty easy. Cut the female threaded fitting off to use it as a tightening nut, and now you have a 1.5" PVC fitting in a 1.5" hole. 1.5" can flow 1200+GPH pretty easy, I was getting 1200+ on mine when it was duroso, now much more as herbie. Specs say 1600GPH, with gravity feed.

not sure i understand what you said at all lol im a newbie with plumbing and this is my first tank with a sump, it was all pre-plumbed, drilled etc. im just trying to make it less noisy.

[Magma]

http://i265.photobucket.com/albums/i...9/stockman.jpg

anyone used the stockman style before?

[monocus]

i switched from a durso to a stockman and i'm very happy with it-takes up way less room and is matinence free

[sphelps]

A stockman works fine but it's a little harder to make. If you can fit a 2" coupling in your overflow then use 1.25" pipe and a 1.25"x2" bushing. You'll have to drill or grind off the bushing stop so the bushing can slide onto 1.25" pipe far enough so the pipe protrudes far enough through the bushing to allow a 1.25" cap to fit. Just as with the stockman you'll need a 1/8" hole in the top of the cap to prevent siphon. You'll also want a 1.5x1.25" bushing for the top of the bulkhead for the standpipe and you'll still want to reduce the drain pipe size to 1" for best results.

A good tip when building a standpipe is to make it taller than you need and then trim the base of the pipe to fit after it's built.

[Lampshade]

Quote:
Originally Posted by Lampshade
A cheater way is to not use a bulkhead.... if you get a male threaded 1.5" PVC fitting, a flemale one and a soft O-Ring you can make a bulkhead out of it pretty easy. Cut the female threaded fitting off to use it as a tightening nut, and now you have a 1.5" PVC fitting in a 1.5" hole. 1.5" can flow 1200+GPH pretty easy, I was getting 1200+ on mine when it was duroso, now much more as herbie. Specs say 1600GPH, with gravity feed.

not sure i understand what you said at all lol im a newbie with plumbing and this is my first tank with a sump, it was all pre-plumbed, drilled etc. im just trying to make it less noisy.

generally people use bulkheads that look like this:


What you can do is use this male adapter:


and make a nut for it by cutting a female adapter off at the threads:


You will need a seal still, so using the seal from a bulkhead, or finding one in a hardware store works fine.


The only reason to do this is to get a little bit extra flow through a smaller hole. With a bulkhead you are inserting a bulkhead into the hole, then a pipe into the bulkhead, this reduces the hole size that water actually flows through.

[sphelps]

I'd stick with using a bulkhead.

[Magma]

making a stockman pipe right now...let you know how it turns out..

Just hate that I had to buy a full 10ft stick of 1.5" PVC just to use 20" or less