how many times a hour should the water go through the sump?

[freezetyle]

Originally Posted by Mr OM

If you skim it 100% then what you return to the tank is clean, if you skim 10% of it then 90% of what you return is dirty or unskimmed, why would you do that when it costs more money in hydro and pumps to do worse?

I understand that. But say, someone was using there return pump for extra flow to their tank. The extra water movement through there wouldn't technically affect the skim-mate that is pulled out of the water.

That being said, there is no actual way to test out these theories as a skimmer pulls out skim-mate in both situations. This test would be almost impossible because everyones tank (or say a "test tank") would differ from one another so getting a control would be practically impossible. I am not saying your opinion is wrong/invalid , I am just saying that in my opinion the flow rate through your sump isn't a big thing to lose sleep on.

[golf nut]

Originally Posted by freezetyle

I understand that. But say, someone was using there return pump for extra flow to their tank. The extra water movement through there wouldn't technically affect the skim-mate that is pulled out of the water.

That being said, there is no actual way to test out these theories as a skimmer pulls out skim-mate in both situations. This test would be almost impossible because everyones tank (or say a "test tank") would differ from one another so getting a control would be practically impossible. I am not saying your opinion is wrong/invalid , I am just saying that in my opinion the flow rate through your sump isn't a big thing to lose sleep on.

I would hate you to lose sleep, however the flow past the skimmer is directly proportional to it's performance.

From my first post I mentioned that PROVIDING the flow in the tank is moving correctly then a 1 to 2 times turnover rate is more than adequate and anything else id disadvantageous.

If I give you phone numbers for the top ten skimmer manufacturers would you call them and tell them they are wrong?

Just a question to you, do you think that a 10% water change done everyday is the same as a 100% water change every 10 days?

[freezetyle]

Originally Posted by Mr OM

Just a question to you, do you think that a 10% water change done everyday is the same as a 100% water change every 10 days?

No they are not the same. My comments were not made as an attack, which it seems to me is how they were taken as per the condescending tone in the last post. I understand that slower flow would result in better skimming due to less dilution from mixing the skimmed water with the DT water. that is also an example of your water change remark. a 100% water change is a lot different that 10%/day.

I were merely stating my opinion and am done on the matter. Anything else feel free to pm instead of filling up the boards.

[golf nut]

Originally Posted by freezetyle

No they are not the same. My comments were not made as an attack, which it seems to me is how they were taken as per the condescending tone in the last post. I understand that slower flow would result in better skimming due to less dilution from mixing the skimmed water with the DT water. that is also an example of your water change remark. a 100% water change is a lot different that 10%/day.

I were merely stating my opinion and am done on the matter. Anything else feel free to pm instead of filling up the boards.

I answered a post, I was challenged with my answers and replied to the questions, I would be happy to PM you so the boards are uncluttered, but why?

PM sent

[Milad]

so did my thread just get hijacked?
all i wanted to know was should i buy a 1325gph pump or a smaller one, lol

[golf nut]

Buy the smaller, cheaper, practical, more efficient one.

[danny zubot]

These theories are all based on the idea that your sump is a filter. While it may seam that most of the water cleaning devices people use are situated in the sump, this doesn't make the sump a filter. It's a place to house filtration equipment. I view my tank, my sump, my refugium and all of the plumbing in between as 1 body of water. So to me it doesn't matter how much flow goes through my sump because my skimmer would work the same down there as it would hanging off the side of my tank, or in my refugium.

As Levi said, the skimmer works at a set rate so it shouldn't matter how much flow is churning around it.

[golf nut]

Originally Posted by danny zubot

my skimmer would work the same down there as it would hanging off the side of my tank, or in my refugium.

That part of your statement is not true it would work better under lower flow circumstances,
it would be more effective hanging on the back of your tank than being in the sump with a 10x turnover rate.

[MikeInToronto]

Originally Posted by Mr OM

That part of your statement is not true it would work better under lower flow circumstances,
it would be more effective hanging on the back of your tank than being in the sump with a 10x turnover rate.

I was with you up until this post, and that's mostly because I was having trouble understanding both sides until now. However, a tank + sump is a closed system. The amount of water running through the sump should be irrelevant. It would be the same as a HOB skimmer running in a sumpless tank with 100x turnover using just powerheads. In this case, the DT is just like a big sump (since there is no sump).

Water in the sump is the same water as the DT. There is no special separation between the two except the OF, a pump, and some pipe.

The concept that "a sump is not a filter" is a good one. A sump really is nothing except a place to store equipment.

Now if your argument is that a low-flow overflow extracts surfactants better, perhaps you can discuss that more.

[MikeInToronto]

To the OP, I believe the recommended rate is ~5x but this is only what I read.

"I saw it on TV so it has to be true!"