Bullet 2 skimmer operation?

Beza · #1 01-26-2010, 12:27 AM

Quote:

Originally Posted by whatcaneyedo

How much clearance do you have above the water level in your sump?

I think the big issue that the instructions want you to avoid is having too much back pressure after the gate valve because that would make it impossible to set the internal water level where it needs to be... Try setting it up the way you want and see if it works. If you find that even with the gate valve wide open you cant get the water level in the skimmer low enough you will know that there is too much back pressure because its submersed.

Yeah Whatcanyedo, that is the conclusion I came up with too. I figure I'll set up my sump so that I can have a minimum water height of 12", build the skimmer booster seat, and then adjust the water height from there based on skimmer operation. I was screwing around with it a bit and I still think that as long as the outlet water level is below that of the skimmer chamber I should probably be ok.

Quote:

Originally Posted by asmodeus

the water level isn't going to matter with a beckett.

Asmodeus, ha haa ha, please elaborate.

Beza · #2 01-26-2010, 01:06 AM

Thanks for all the input guys!

I think my question comes down to the idea of putting a skimmer BELOW the water line, which as far as I can tell is not going to work, given that the bullet 2 is open to the atmosphere. If anyone has tried this, please let me know! I am pretty sure that as long as you had a pump that was powerful enough, you could put a beckett style skimmer as high as you wanted... but the point is that I would like lots of volume in my sump, in addition to keeping the space it occupies to a minimum. Here's what I have on my drawing board so far:

So as you can see, clearance is going to be an issue. I think that I can raise the skimmer a bit and still be ok all around. I'll post the new sump plan when it's finished.

Skimmerking · #3 01-26-2010, 01:22 AM

Quote:

Originally Posted by Beza

Thanks for all the input guys!

I think my question comes down to the idea of putting a skimmer BELOW the water line, which as far as I can tell is not going to work, given that the bullet 2 is open to the atmosphere. If anyone has tried this, please let me know! I am pretty sure that as long as you had a pump that was powerful enough, you could put a beckett style skimmer as high as you wanted... but the point is that I would like lots of volume in my sump, in addition to keeping the space it occupies to a minimum. Here's what I have on my drawing board so far:

So as you can see, clearance is going to be an issue. I think that I can raise the skimmer a bit and still be ok all around. I'll post the new sump plan when it's finished.

Well ok i will jump in again since Im on a role here i had a skimmer on the ground floor and the sump was the same leve ldidnt mater i just had the water level to run at a certain level due to the sump height really easy actually

Beza · #4 01-26-2010, 04:25 AM

Thanks for the input guys! It's been a big help!

So here's what I'm planning with the sump. It's my rough outline, so be gentle! Lol. You'll notice that I have the skimmer a few inches into the water level.

Please let me know if there is anything I am obviously missing, or anything you might think of to make the design better before I go out and start bugging glass and plastic companies all over town for scraps!

Skimmerking · #5 01-26-2010, 01:32 PM

it looks good man well done the baffles are the correct way

Skimmerking · #6 01-26-2010, 01:17 AM

Quote:

Originally Posted by Beza

Yeah Whatcanyedo, that is the conclusion I came up with too. I figure I'll set up my sump so that I can have a minimum water height of 12", build the skimmer booster seat, and then adjust the water height from there based on skimmer operation. I was screwing around with it a bit and I still think that as long as the outlet water level is below that of the skimmer chamber I should probably be ok.

Asmodeus, ha haa ha, please elaborate.

oh ok I will little grass hopper. When you have a venturi skimmer there isnt any way of controlling the water the water leve land its pressure will control the water in the skimmer hence the water level.

Now with the Beckett's you have a gate valve that is controlling the water level and hence keeping wht water level at what eve you turn the gate valve too. hows that. that should make sence for ya.

Skimmerking · #7 01-26-2010, 01:19 AM

with your clearance then running the skimmer out side then you have alot of room in the sump for other things. that is the great thing about Becketts power. and EXternal