![]() |
|
View Poll Results: How Long Do You Mix A Fresh Batch Of Salt Before Putting it in the Tank? | |||
A Couple of Hours |
![]() ![]() ![]() ![]() |
47 | 28.66% |
12 Hours |
![]() ![]() ![]() ![]() |
8 | 4.88% |
24 Hours |
![]() ![]() ![]() ![]() |
59 | 35.98% |
2 Days |
![]() ![]() ![]() ![]() |
35 | 21.34% |
However Long it Takes the Heater to Get it to Temperature |
![]() ![]() ![]() ![]() |
15 | 9.15% |
Voters: 164. You may not vote on this poll |
![]() |
|
Thread Tools | Display Modes |
#11
|
|||||
|
|||||
![]() In an emergency I've mixed and used it inside of five min's. Most of the time it's more then a week. I have two 35 gallonish rubbermaid cans, one for RO and one for Saltwater. I have a 900gph pump running continuously on the salt side to keep it mixed. I've never heated the water.
__________________
Robb |
#12
|
||||
|
||||
![]() I mix my salt until it is all dissolved, < 5 min, using tank temperature water and pump it in as I siphon detritus and old water out. Been doing that for years. Change 10% water every week. Fish and corals are in excellent condition.
|
#13
|
|||||
|
|||||
![]() about 10 - 15 min, as soon as I can see clear to the bottom of the bucket, it goes in the tank
|
#14
|
|||||
|
|||||
![]() Anywhere from when it's clear (after adjusting for salinity) to a couple days ahead... If too much water evaporates from my mixing bucket (I try to avoid this anyhow, distilled water isn't cheap) there is a white deposit left on the pump and bucket since I dose the freshly mixed water with calcium and magnesium while it's mixing. The pump heats the water to a reasonable temperature also, so I don't use a heater.
__________________
Calvin --- Planning a 29 gallon mixed reef... |
#15
|
||||
|
||||
![]() Usually a day or two, although instructions usually say that it can be used immediately (but reccommend aerating until O2/CO2 equilibrium is met) not sure how I would measure that.
|
#16
|
|||||
|
|||||
![]() Voted 2 days but usually now plan for a week (a couple of days the fresh ro/di aerating, then few more with the salt). In the old place with FOWLR, used tap water and de-chlorinator in a bucket in front of the tank and as soon as I dissolved the salt, mixing with my hand, had a water change going.
__________________
my tank Last edited by mark; 09-10-2009 at 01:58 AM. |
#17
|
|||||
|
|||||
![]() I voted a couple of hours just because it was the shortest time increment. I'm with Christy, I usually mix it for as long as it takes for the water to clear. Which is usually the time it takes me to do all of my other water change tasks. I'm kind of bad with the heat thing though. I don't heat it up as I usually have it stored in jugs at room temp. It does lower my tank temp a couple of degrees but nothing bad has ever really happened while doing it this way. The way I see it cool and warm currents move through reefs all the time, changing the temperature for a while. So in a way, I feel like I'm copying a natural occurance.
__________________
THE BARQUARIUM: 55 gallon cube - 50 lbs LR - ASM G3 skimmer - 30 Gallon sump - 22 Gallon refugium / frag tank - 4x 24 watt HO T5's - Mag 9.5 return - Pin Point PH monitor - 400 watt XM 20K MH in Lumenarc reflector - Dual stage GFO/NO3 media reactor - 6 stage RODI auto top up -Wavemaster Pro running 3 Koralia 2's. Fully stocked with fish, corals and usually some fine scotch http://www.canreef.com/vbulletin/showthread.php?t=55041 |
#18
|
|||||
|
|||||
![]() I didn't vote, the salt can be mixing anywhere from 5 min to 2 months
|
#19
|
|||||
|
|||||
![]() Always 3 days,just what i've done.
|
#20
|
||||
|
||||
![]() Sounds like it doesn't matter a ton either way....
|