|
|
|
#51
03-30-2008, 05:08 AM
|
|||||
|
|||||
Quote:
|
|
#53
03-30-2008, 03:54 PM
|
|||||
|
|||||
|
Crazy man that Ed is! We are tentatively planning a trip up to Edmonton at the end of April. So Ed I guess we should coordinate something, and you too Rigger11, we want to get together with you as well.
|
|
#54
04-02-2008, 03:54 PM
|
|||||
|
|||||
|
A much needed update;
The glass for eurobracing has been ordered, someone just needs to pick it up. Its available tonight. The required mermaid photos;   The wood for stand, storage closet, and hood  This was yesterday;       
|
|
#55
04-02-2008, 04:51 PM
|
|||||
|
|||||
|
Looks great, Catherine. I wish I had y'alls mad tank-makin' skillz!
__________________
~Drew 10G Nano * 10G Sump * Deltec MCE 600 Skimmer * JBL Viper 150w MH * Zeovit * Vortech MP40W Millions long for immortality who do not know what to do with themselves on a rainy Sunday afternoon. ~S. Ertz 
|
|
#56
04-04-2008, 05:50 AM
|
|||||
|
|||||
|
lol I love the livestock!
Any reason you didnt make the corner braces on the stand go from the floor up to the top of the stand (rather than between the horizontal pieces as you did)? I just figure it might be stronger to transfer the weight of the tank to the floor via single pieces of wood rather than three distinct pieces.
|
|
#57
04-04-2008, 06:34 AM
|
||||
|
||||
|
The single top layer is best, as it will end up being flatter. I would have the legs go all the way down on mine and just built the bottom frame inside the legs. Just personal preference. One it is all screwed together, the legs and the bottome frame will move and act as one, transfering the weight to the floor evenly along the whole bottom.
|
|
#58
04-04-2008, 12:51 PM
|
|||||
|
|||||
|
The reason I did it this way is so that not a single screw is taking any weight....the screws are just holding the wood together!!!
__________________
500G Mixed Reef  __________________________________ Electrician, Electronics Technician, I can help with any electrical questions you might have!! __________________________________ Kevin Last edited by KrazyKuch; 04-04-2008 at 09:50 PM.
|
|
#59
04-15-2008, 11:59 PM
|
|||||
|
|||||
|
Much Needed Update
Well it's been a couple weeks but We finally got our glass for the overflow and Euro Brace. Also did some more work on the stand, got the plywood down and the foam so it's ready to go!!
The Euro Brace is 5/8" thick and 4" wide, The overflow is 5/8" thick and is 6" deep, the two side supports for the overflow is 3/4"(reason for such thickness is that bow valley had scrap pieces kicking around so we got them cheap!) Stand so far!  Shot of the plywood!  Glass for the Euro Brace and the Overflow!      Black acrylic for the overflow!  Overflow in Place!   Shots of back Euro brace being attached   Attaching the side pieces of the Euro brace  
__________________
500G Mixed Reef __________________________________ Electrician, Electronics Technician, I can help with any electrical questions you might have!! __________________________________ Kevin
|
|
#60
04-16-2008, 06:18 PM
|
|||||
|
|||||
|
We are planning a Tank Lift party on Sunday May 4th. We'll be offering BBQ foods along with Rock Band. By that time the tank should be drilled and ready to be set up on the stand.
|
Linear Mode
