Needlewheel to Meshwheel skimmer mod

[Delphinus]

Depends on the impeller I think, in my case the blade worked fine. If it's stiffer/stronger plastic then maybe a dremel.

The pictured venturi is intended as a replacement of the "stock" venturi .. (yes it would go onto the pump intake ) I'm sure it's an improvement whether the skimmer is recirc or not .. the idea here is just to get more air into the skimmer.

I could be mistaken, but I get the impression that it's only the larger skimmer folks who are using an airpump to drive the air injection.

[Jaws]

So I finished the meshwheel mod about an hour ago on my Euro Reef CS8-3+, and everything went really well. This skimmer has two sedra 5000 pumps and is pretty much the same as the RS 250. There's definitely more bubbles except now it overflows. I've got the gate valve dialed all the way down too. Before, I tried to adjust the skimmer so the water line was just below the collection cup. Now it's right at the top of the collection cup just below where it overflows. Before I cleaned the collection cup neck the skimmer was producing skimmate but it was very wet. After I cleaned the collection cup the skimmer now just overflows clear water. There's still tons of bubbles in the neck but it's only producing clear water, no skimmate. Any ideas what I can do to help this?

[Delphinus]

I think it will get better as it settles in but you might want to think about slowing the feed pump maybe.

That's awesome you get such results, I didn't get anywhere near that kind of "my cup is overflowing like crazy" type results and I thought it was maybe because of the Sedra .. so you just proved that theory wrong.

Can you snap a picture of the pumps? I'd like to see how they sit on the skimmer itself, maybe I can change how I have mine and get some more improvement that way.

[Jaws]

Originally Posted by Delphinus

I think it will get better as it settles in but you might want to think about slowing the feed pump maybe.

Can you snap a picture of the pumps? I'd like to see how they sit on the skimmer itself, maybe I can change how I have mine and get some more improvement that way.

It's not a recirlution skimmer so there are no feed pumps other than the actual pumps I did the mod to. I've been running one pump at a time for 8 hours each to try and help break them in. With only one pump turned on it sure generates a lot of foam at the top after a while but because there's only one pump on it's not enough to push the foam up the neck so it can overflow in to the collection cup. As soon as I turn the second pump on the water level goes right up to the top of the neck again and overflows wet, large bubbles in to the collection cup filling it up pretty quick. The bubbles overflowing are large because there isn't enough height to form a foam. I've also noticed quite a increase in turbulence in the skimmer including the neck and not all the bubbles are really fine. There are some bubbles the size of a tic tac hovering around in the neck too. I've also adjusted my auto-topoff so the water level in the sump drops which has always lowered the water level in the skimmer too. I'll see if that helps.

The pumps sit horizontally just like in this picture:

http://www.jlaquatics.com/phpstore/s..._ID=ps-errs250

[Delphinus]

Huh - go figure - I had figured that all multiple pump skimmer designs were recirculation style. I.e, the pump draws water from the skimmer body and the water feed to the skimmer itself is independent of the needlewheel (meshwheel now) pumps.

I had to mod my ASM to be recirculation, basically all I did was drill a new 1.75" hole (the 1" uniseal requires a 1.75" hole same as for a 1" bulkhead) and hooked the pump in that way. For the last year I've been feeding the skimmer via a T off the overflows, now I'm feeding with a maxijet 600 (after trying a maxijet 1200 for the last week). I read on asmskimmer.com/octopusskimmer.com that for a recirc skimmer you want a feed pump about 1.5 times your tank volume (but I'm not sure if that number is just a WAG on their part - I don't know if there are any metrics applied to generate that factor value of 1.5).

Seems to me you might need to think about modding the skimmer itself. The problem is that the pumps are just pushing too much volume of the air/water mixture for the exit pipe to carry out fast enough. You could start by trying to raise the skimmer so that there is a larger height differential, but it sounds to me if you're racing water through the skimmer that it doesn't have a lot of contact time. So going towards a recirc mod on your skimmer might be something to look at.

I'm not sure what I'd do. Bear in mind this is all black magic to me, so don't just follow MY advice because I'm clueless!!

[Chin_Lee]

jason
try to control the amount of air entering the venturi with a small valve and it should decrease the bubble level. as the pump breaks in more, increase the air flow to raise the bubble level.

[Jaws]

It's actually already started to settle down and I got 2" of stuff in the first 24 hours. It's definitely not as dark as the old stuff but it used to take a week to make what the mod has done in 24 hours. So far I'm happy and look forward to seeing the long term effects of this. The water line is still almost right to the top but the skimmate is thicker and darker now than the wet bubbles that it started pumping out first.