|
|
|
|
|
#1
04-13-2007, 03:31 PM
|
||||
|
||||
New firmware 3.02!
As promised:
The new firmware & manual 3.02 is available here: http://www.ghl-kl.de/Produkte/Aquari...LuxII_V302.zip http://www.ghl-kl.de/Produkte/Aquari...LuxII_V302.pdf The IP-address can be entered now directly on ProfiLux, please read chapter 3.15.16 Communication. And it is possible to change from ad-hoc to infrastructure-mode (only interesting for WLAN). The attached photo shows entering an IP on the ProfiLux. 
|
|
#3
04-13-2007, 06:24 PM
|
|||||
|
|||||
|
Very Nice Matthias!
This is a huge step in the right direction. Now it is much easier to connect to the Profilux from anywhere with an Internet connection. From what I gather all you need to do now is install Profilux Control on any computer (like at work) and you should be able to connect to your Profilux @ home. (so long as you have access to port:10001 traffic on both sides) This is MUCH MUCH better.
|
|
#4
04-13-2007, 07:14 PM
|
|||||
|
|||||
|
thats awesome matthias. now i'm actually excited to try and get the wlan setup again.
|
|
#5
04-14-2007, 06:37 AM
|
||||
|
||||
|
Thanks for the feedback!
The connection over internet is no problem, too. I tried this here at home - it works absolutely reliable. These are the steps to establish a connection from somewhere to the ProfiLux at home: - You need a domainname for at home, like www.mydomain.com. You can obtain this at DynDNS for example - Install ProfiLuxControl II on your "remote" PC (eg at work) - Edit the connection-options -> Hostname is now NOT the IP-address of your ProfiLux (eg 192.168.0.169) but your domainname (eg www.mydomain.com). Under "Hostname" are IPs AND domainnames accepted! - configure your router at home: incoming tcp-calls on port 10001 must be redirected to the IP of your ProfiLux (in this example 192.168.0.169) Last edited by Matthias Gross; 04-14-2007 at 06:43 AM.
|
|
#6
04-15-2007, 02:21 PM
|
||||
|
||||
|
Is anyone using V3.01 or above firmware with Digi plug bars via USB expansion?
|
|
#7
04-15-2007, 03:10 PM
|
||||
|
||||
|
yes, Michael.
Me & most of USA/CD customers. And all customers worldwide with digital powerbars. (some may have still 3.00, others may have 3.02) I think in sum about 300.
|
|
#8
04-15-2007, 06:18 PM
|
||||
|
||||
|
Just wondering if this unit can controll pumps that operate on AC? eg. SEIO's and Koralia's.
Also, what is the compatability between these and the Vortech? Thanks, Albert
__________________
This and that.
|
|
#9
04-16-2007, 01:34 PM
|
||||
|
||||
|
Hi Matthias,
Can an IP-address be entered on the Profilux even if I don't have the LAN/WLAN card installed on my Profilux ? I would like to try to connect using a D-Link Wireless USB adapter, that would be plugged into my RS232-to-USB adapter ? Would this work ? Thanks, Ginzo Quote:
|
|
#10
04-17-2007, 06:04 AM
|
||||
|
||||
|
Hi
@Albert: Not all pumps can be dimmed by the reduction of the voltage (AC-side). It depends on the motor type, the pump-producer can give this information. If the pump is dimmable by reducing the mains voltage you will be able to control the pump with our new dimmable socket - coming soon. Vortech: I can't promis this feature at the moment. @Ginzo: That doesn't work. These USB-WLAN adapters are constructed for the PC-side, you can't connect it to ProfiLux. It's the same like connecting a USB-WLAN to a printer or other device - not possible.
|
Hybrid Mode
