Marc`s 1k gallon system.

[christyf5]

Love the avatar Marc

That last reactor pic is pretty impressive. I like the idea of adding the extra chambers for other media. Smart idea

[justinl]

hahaha awesome avatar.

beer always makes projects go more smoothly. Im a sleeman's fan myself.

[SuperFudge]

A couple of small projects,

The Stirrer was a simple mod,

If you look at the top flange set of the old ca reactor in the pics above, you can see where the new stirrer body came from.



I just hacked the top half off and replaced the bottom, and routed out the flange to accept the motor casing off the old stirrer.



All i really did here was increase the body size so it could accept more kalk without bogging down the stirrer too much.



You know your in a sad state when you take a Deltec and make it into a DIY.

The reseviour,

This was an old 220 plexi that had a corner blown out of it...so i repaired it and put it into use.



I wanted to keep it simple and use only one pump for mixing and pumping to the tank.

In this pic`s lower left you can see the valves used to do this.
When they are in the position shown, the pump inside is feeding up through and back into the res for mixing.



Then when waters needed i just have the valves oppposite to what is shown, then it uses the same pump to push water into the sump after a water change.

Also in this pic you can see a small blue valve....this is plumbed into the intake of the pump, this was done becuase the feed to the sump is running along the floor back up over the sump edge.
I didnt want water to go stagnant in this line when not in use....so this small line acts as a venturi, when the water change is done, i open the small blue valve and it suck all the unused water out of the lines running along the floor.


Many Projects yet to come....

[untamed]

Can you provide some details on those vaccuum hoses that are hanging on the side of your mixer? It looks like you've got a powerhead hooked up to one, and they both have union fittings on one end...I would love to see how these work because I need to create something like that myself.

[krisalexander]

Marc enjoying the ride, I am learning more on this thread, than if I were paying attention in class instead of reading this!
Also that is a hilarious quote at the bottom of your signiture.

Keep it coming,

Kris

[demon666]

this is a great thread giving me many ideas for when i move and redesign my setup

[blaster]

Ya those vacuum hoses interest me also.Its to hard to get into my sump to siphon.A mark mod would be great.By the way thxs for sharing your ideas.

[mark]

Any pictures of setting and sealing of the viewing panels?

[SuperFudge]

Sorry...im slow i know, being sick this weekend allowed me to have time to scour for pics.


The largest amount of time and effort was put into the skimmer(s).
Always an ongoing saga for me, on this system it started here....

The first trial was another single beckett injected skimmer similar in size to a Bullet 3.
This one i knew was a bit undersized at the time, so an experiment was done using a single housing, but 2 becketts in it.
This one also had a spray bar to clean the neck, a later scrapped idea.





To be honest, i dont think that one even got anymore than tested before another was built.

The next one i wanted to try several idea`s, I hated most venturi`s becuase of the too small holes in them...so i wanted to make my own type.

These i made out of solid acrylic, so i could see if they got plugged or not.





Here is how i tested them,







The skimmers injector housing had to be removable to continuously change and test these, aswell as injector tower hieghts.

Here`s a version with 2 of them,





These were being tested while the skimmer had no change in neck diam and no cup to speak of.
In these pics you can see i just bulkheaded the top, and it just spit the foam out the side.



Then another injector was added ,aswell as heightened injector towers.



And an auto shut off.... good testing requires that you flood out your house several times during your build before making one of these.



Then, for some unknown reason, i had to play more...

[SuperFudge]

Almost forgot,

I made a self cleaning head a few weeks back aswell,





heres a crappy vid i did with the camera, excuse the poor quality.




Marc.