Tunze Nano Streams

skylord · #1 01-29-2007, 12:11 AM

My first one was very noisy so I took it apart and the impeller shaft was sheared off. It was replaced for me and now the two I have make almost no noise at all. Very quiet.

Scott

Der_Iron_Chef · #2 01-29-2007, 01:02 AM

Quote:

Originally Posted by skylord

My first one was very noisy so I took it apart and the impeller shaft was sheared off. It was replaced for me and now the two I have make almost no noise at all. Very quiet.

Scott

Yeah, I took mine apart to clean/inspect it, and the impeller/propeller shaft was also sheared off (the metal rod that holds the propeller on was rusted and had broken off). Weird! But it was also replaced for me where I bought it here in Calgary. Gotta love good customer service.

JasonJ · #3 02-13-2007, 05:27 PM

hey guys
my nanostream 6025 just started making a really loud noise. it was quiet before. ive only been using it for maybe 3 weeks now. i checked the impeller seems fine. any ideas?

muck · #4 02-13-2007, 05:29 PM

broken shaft?

Buddyboy · #5 02-13-2007, 06:37 PM

Jason,

Lots of people have been having trouble with this initial run of nanostreams. My 6025 has been fine, but many people have been having problems.

Confirm that the impeller shaft is straight and not moving around (ie you can't pull it out). If not, go over to www.reefcentral.com and go to the Tunze forum. Ask the same question of Roger over there. He's a very helpful guy!

If that doesn't work, you might need to return the pump and get a new one. I think the Canadian distributor is Proline Aquatics.

And most importantly, good luck! Let us know how it goes.

Okguy · #6 02-13-2007, 08:03 PM

Mine's also been fine but you might want to read this post.

http://www.aquariumpros.ca/forums/sh...ght=nanostream

Sounds like you will have very little problem getting it replaced

JasonJ · #7 02-13-2007, 08:25 PM

turns out the metal shaft rusted and broke off.
so JL gave me a new one. they said only the first batch of these guys has that problem.
Mike from JL said that the metal shaft shouldnt be comin off. when he pulled it ..it just came right off all rusted.

all is well.
thanks.

Rippin · #8 02-14-2007, 05:23 AM

Well, just installed two 6025 nanostreams in the 50g aquarium.

This was the setup BEFORE the Tunze powerheads:
Seio 1500
Fluval 303 (for carbon and surface aggitation)
Deltec MCE 600, which actually has a decent amount of flow for a HOB skimmer.

The two 6025 replaces the Seio and the Fluval 303 canister.

The flow is now slightly greater and definitely more diverse.
It's actually quite amazing - if you place your hand in front of the Nanostreams it doesn't feel as strong as the Seio 1500, but it does just as good a job for flow.

Installation was quite easy, although you have to take some precaution as the plastics are thinner than standard powerheads. Definitely take seriously the warning of placing the two magnets close to each other. If they are within a few inches of each other they will snap together and you'll have a h&ll of a time trying to get them apart. Don't use this product if you have a pacemaker

With 3/8 of an inch of glass between them, it's no problem.

Start-up was almost immediate. If you hear some clanking on start-up, disconnect the power and try connecting again. It shouldn't take more than a couple of tries to get it running in the correct flow direction.

Noise-wise it's a bit louder than the Seio 1500 which is very quiet, even more so for it's size.

IMHO, two 6025 is enough for a 50 gallon aquarium. In conjunction with the Deltec skimmer, total flow and coverage is almost perfect. I have about 65 lbs of live rock.

We will see how this product fairs in the long run.

Cheers.

Der_Iron_Chef · #9 02-14-2007, 05:32 PM

I'm frustrated for the second time with my second Tunze Nanostream 6025. The first time, the impeller shaft rusted/broke up, like mentioned above. So, it was replaced by the retailer.

I just turned off the pump to feed the fish, and now it won't restart. I know people are mentioning having to reset it a dozen+ times....grrrr. What does "reset" mean anyway? Unplug-plug...and repeat X12...or until it starts?

I'm just suprised that Tunze has marketed a product which seams to have an increasing number of emerging design flaws. I will say that, when it's operating, it operates well. So I'm not completely un-sold on this item :-)

Dave C · #10 02-14-2007, 05:35 PM

Yeah, I turn it off and on until it stays on. You have to give it about 5 seconds before you decide it's not going to fire up. Sometimes it kicks in during that time. It's completely random too, sometimes it works right away, others not.