Profilux II plus aquarium controller

[bullit67]

All is well here the controler is working good now the problem with the one socket staying on has gone away will keep an eye on it to see if it happens again just need to mount the level sensor and the Propeller Breeze. hope to get it done this weekend and then i will work on the LAN card On that not Jason are you getting any of the speed controls for the propeller Breeze if so I need one. Also do you know if the new 6 socket power bar can be chained together with the 4 outlet bars ? I need one of thoses too alittle off topic but is it you (Jason) that brings in the wavyseas? if so do you know if they make a extention for the control wire?

Well I better get out side and start shovleing


Later Doug

[support@proline]

Hay Doug
Good to hear from you.
The 6d & 4d can't be chained however ,however talk to mike & I am sure he can aarange something for you
The propeller breeze control is in stock & mike should have a couple in stock my friend.
As for wavy sea I will ask the manufacturer & let you know.
Have fun shavelling my friend ,I did some earlier,Damn it's cold

[niloc16]

again i came home and found my one tunze off again. i am not using the y adapter i have each pump connected to its own port, when i swapped ports the problem swaps pumps, i have triple checked my programming and all seems good. again, is turning the pump off part of the random current generator?

[SuperFudge]

Colin,

Tommorow afternoon i will take the tunzes off the other controller and try it on the profilux.

Ill let you know what happens.

Marc.

[niloc16]

thanks marc. its happened two days in a row now

[Matthias Gross]

Hi niloc,

Did you read my last post about tunze?
Please give me detailled information about your configuration regarding the pumps. Where are they connected, what cables do you use?
After that i will tell you how to do the proper settings.

[niloc16]

they are using the tunze 1 and tunze 2 cables, one is installed in L1-L2 and the other installed in L3-L4, 1-10v port 1 is set to current pump1 and 1-10v port 3 is set to current pump2, random flow, min volt4 and max volt 10, nocturnal decrease to 30%, max flow of both pumps 100% and min flow of both pumps 40%. wave 30s, min duration 30min max duration 1hr 30min (unsure exactly the use of this setting but that is what it is set ). i believe that is all the settings they are set to. let me know if i missed something that you need to know

[Matthias Gross]

niloc16,

i think i found the mistake.
Cable ProfiLuxTunze1 uses L1 (or L3 when used in L3L4), cable ProfiLuxTunze2 uses L2 (or L4 when used in L3L4). So we have two different Tunze-cables, they can be connected to one port (eg L1L2) using an Y-adapter, then L3L4 would be free for other purposes.
That means in your case: 1-10V port 1 (=L1) and 1-10V port 4(=L4!) should have function pump 1 and pump 2! (Assuming you connected Tunze1 to L1L2 and Tunze2 to L3L4, otherwise we talk about the 1-10V-ports 2 and 3).
So please configure 1-10V-interface 4 - then it should run.

[niloc16]

thanks matthias, this will probably drive you nuts, but with the cables out of the bag is there markings one them to determine which one is tunze cable1 and tunze cable 2? now that i have been swapping them to troubleshoot i dont which is which.

[Matthias Gross]

bullit67

the digital powerbars can be connected to S1-S4. This port can programmed to control standard OR digital powerbars. Because the digital powerbars can be "daisy-chained" up tp 4 digital powerbars only need one port.
The other port, S5-S8, is always suitable for standard powerbars! So a mixed setup is possible.
For the use of digital powerbars a firmware-update is neccessary. Firmware 3.00 + new manual will be available soon for download. Besides the digital powerbar support we added a lot of new nice features, eg extended controlling options for heating, pH....