Profilux II plus aquarium controller

[SuperFudge]

Im pretty sure its in the settings somewhere Doug.

Heres a couple thoughts, I have to reference them to my controller yet to be sure..but have to do that yet.

-You may have set this as "permanent" outlet.
-setting the number of days..i think this was correct when you where explaining this to me..but wanted to throw it out there.
-im unsure but also check the dimming curve settings, if they have been accidentally assigned to an outlet this can also influence the outlets,
aswell if "automatic operation" has been enabled.
this was a source of my initial trouble.
-Set for filter...this may have been a standard factory setting for that outlet or accidentally assigned...this will remain permanently on, im unsure if the timer only influences the LED in that case.

Anyways...i hope something will come up here.

Marc.

[niloc16]

how do you put halides on a timer. all the manual talks about is dimmable lighting. i've selected an outlet to be set for lighting but i cant figure out how to put it on a timer without dimming

[Matthias Gross]

Hi,

@niloc16:
If you are following exactly the tutorials hints it should be possible to establish the connection. Till now we have several dozens of WLAN-Users, anyone got it running.
I wonder why you had connection with DeviceInstaller as mentioned in earlier posts - but now it seems DeviceInstaller does not find the device?
Important (this is mentioned in the tutorial):
1. The first connection (to do initial settings) must be done directly in any case, that means to establish an ad-hoc connection with the WLAN of your notebook, NOT with WLAN of a router or access point!! Then, if available, disconnect the LAN-interface of your notebook!! If there are several network interfaces available it could be possible that DeviceInstaller accesses the wrong one to search the PLM-WLAN.
2. Maybe you did some settings to the PLM-WLAN with the result it can't be found by your notebooks WLAN - in this case do the Reset WLAN to default
3. It is possible that another WLAN-device (router, another PC, ...) disturbes direct connection of PLM-WLAN to your notebooks WLAN -> deactivate any other WLAN-device!!
4.Firewall - sometimes a problem because DeviceInstaller must send broadcast messages to find any PLM-WLAN. Just deactivate the firewall for initial configuration!

After following these points DeviceInstaller should find the PLM-WLAN. If not - it may be possible that your notebooks WLAN-device is not compatible to PLM-WLAN. But - why did you have a connection before this?

@bullit67:
I don't think this is a programming problem. When the LED is off the socket MUST be powerless. LED and switching relay are directly connected. And it seems your LED switches according to your programming.
Did you connect a heavy inductive load to this outlet (eg metal halide lamp)? In this case the fuse can't protect against damages and it might be possible that the relay has been damaged - then the contacts are not able to disconnect safely. You can test this:
When it again happens that the LED is off (LED off means control signal coming from ProfiLux is shut off) and the socket has power just knock onto the power bar. Do the contacts open?
And: Use another socket for the same task - does the socket power now follow your programming?

Good luck!

Matthias

[Matthias Gross]

Hi,

again @niloc16:
There are two ways to switch non-dimmable lamps programmatically.
1. Program a clock timer and assign the function clock timer to the socket
2. Program a dimming curve (of course knowing we don't have a dimmable unit) and only program 0% and 100% dimming points with shortest dimming duration (5mins). Then assign the lighting function to the socket.

Comment:
The new firmware 3.00, released in some days, will differentiate between dimmable and non-dimmable lamps. Then the programming for non-dimmable lamps will be the same as for the clock timers. Another firmware extention will be the temperature dependend shut off for non-dimmable lamps (with delay for metal halides). And some more new features.

Matthias

[niloc16]

thanks matthias, i got my lighting figured out and timed. i calibrated and connected all my probes tonight, i'm suspecting i have the conductivity and redox probes swapped at the connectors because the tank reading for redox is 50ms and conductivity is 0. there was a post on here stating the conductivity connector went on the the post that sticks out of the card and i swore i connected it there but tomorrow i'll have to try again.

[Matthias Gross]

Please connect the redox probe to the upper BNC-plug and the cond. probe to the lower, outstanding plug.
You wrote "reading for redox is 50ms" - this is not possible, even if the probes would be swapped. ProfiLux does not mix units and information. ProfiLux displays for example "Redx1 100mV" OR "Cond1 50mS" but no mixture. I am rather sure - i programmed the firmware.

And: You would have recognized swapping of probes while calibrating...it is suspicious when the display does not show different values (the ADC-Value)for the two calibration points.

I am very sure we will get your complete system running next time!

Greetings