Need some calcium reactor help! A LITTLE HELP WOULD BE NICE

Tarolisol · #1 11-09-2006, 02:12 AM

Well, to keep up with this post.
My magnesium level is 1.100 or somthnig like that, not sure if thats good or bad.

Also i cant seem to bring my calcium up. Ive been adding argamilk for several days now but cant get it above 240ppm. My alk is at about 11-12dKH. Im beggining to think there is something wrong with my calcium kit, or can argamilk go bad.

Also my PH has been slightly increasing it has gone up to 8.45 from 8.3. Cant really explain this.

support@proline · #2 11-10-2006, 03:21 AM

Hi Sean
Just checking on how you doing with this?
your MG should be around 1300 to 1350 ppm, your low MG can cause some problems with the balance.
The Zeomag that you have comming to you can be just placed on the top of the media in the chamber ,stuff is very strong ,please use in the ratio of 10% zeomag to 90% aragonite media.
For a quick Mg fix you can use an additive.any brand will do .
what is your bubble / minute for co2
How many drops/ minute of effluent exits ,the reactor?
Sorry for late response ,but keep us posted please.

Pescador · #3 11-10-2006, 03:49 AM

Aragamilk won't bring your CA levels up. It is basically an aragonite slurry. You need a calcium supplement like Reef Complete (that has Mg as well) or the calcium part of a two part supplement.
Don't dose anything for your alk so it can fall and let your CA go up.
It could take a couple weeks to bring your level up until it's in balance with your alk and then your reactor will maintain it.
You can use a calcium supplement to raise your levels but to maintain them you have to use a balanced two part supplement or your reactor.

Tarolisol · #4 11-10-2006, 03:51 AM

Quote:

Originally Posted by support@proline

Hi Sean
Just checking on how you doing with this?
your MG should be around 1300 to 1350 ppm, your low MG can cause some problems with the balance.
The Zeomag that you have comming to you can be just placed on the top of the media in the chamber ,stuff is very strong ,please use in the ratio of 10% zeomag to 90% aragonite media.
For a quick Mg fix you can use an additive.any brand will do .
what is your bubble / minute for co2
How many drops/ minute of effluent exits ,the reactor?
Sorry for late response ,but keep us posted please.

The reactor is doing probly a dubble per second, maybe slightly less. As for efulent i have no clue buts its probly pretty high since its coming out quite quickly.

kari · #5 11-10-2006, 02:59 PM

After the mg is at normal level maybe use something cheap like calcium chloride (Turbo Calcium) and baked baking soda for adjusting alk and calcium levels.

I'm planning on trying the mg media in the reactor aswell but wonder if over dosing can become a problem. It would be a bummer if levels get too high and the need to dump all the media comes up. Possibly the easiest fix is to use a salt brand with the correct mg content and do some water changes. I find the bottled mg additives get too costly with larger tanks.

Doug · #6 11-10-2006, 04:16 PM

If all measures are correct, then dont add anything that will effect your alk. levels. Plus the reactor is basically an alkalinity reactor, so it will maintain those levels.

I agree with the idea of adding a calcium/magnesium/strontium product, like the mentioned Turbo Calcium or my preference , Seachems Reef Advantage. However their are several on the market.

Adjust it slowly. I would back the reactor down for now, until a balanced calcium & alk. levels are reached. An effluent quanity around 40ml/min. & a bubble count of around 60 or less/min. Ed,s ph suggestions are right on. They can all be increased later as the tank matures & grows. Also it should then maintain both alk. & calcium levels. Most aquarists with larger tanks, esp. with sps, use both reactors. Kalk & CO2.

Or at the least, drip kalk, with a jug or whatever.

Tarolisol · #7 11-10-2006, 08:01 PM

Ok, so im going to turn the reactor down for now untill i get everything correct with additives. I have mg and seachem calcium stuff that i am using to increase it.

Ill post back when i get everything at the right levels.

Thanks, everyone.

Railskinner · #8 11-11-2006, 06:36 PM

I have just set up a calcium reactor as well. Last night

calcium 440/alk 11/ ph 8.3 /salinity 1.023
77 gal/33 gal sump

5lbs tank/ milwaukee regulator/bubble counter/soleniod/needle valve /sms122 controller.Followed intructions for set up and ph was about 7.8. So i raised the bubble counter and then it dropped to 7.4

ATM I have everything working bubble counter set at about 150 drops per minute/ effulent at 180 drops. Ph was at 7.4 This morning I looked at ph controller and it's reading 7.0. I 'm trying to get this down to about 6.5- 6.7. If l turn the bubble counter up more and keep the efulent flow the same will this knock the ph down for me.