Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Tank Journal

Reply
 
Thread Tools Display Modes
  #131  
Old 10-09-2013, 07:54 PM
Kryptic4L Kryptic4L is offline
Member
 
Join Date: Nov 2008
Location: Calgary
Posts: 354
Kryptic4L is on a distinguished road
Default

loving lego man.
__________________
Two clownfish were in a tank. One says to the other, how do i drive this thing?
Reply With Quote
  #132  
Old 10-09-2013, 10:29 PM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

He can't wait for his first swim!
Reply With Quote
  #133  
Old 10-12-2013, 05:55 AM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

Here is the plumbing and miscellaneous work I had completed before leaving for work.

I envision the Mitras ballast top left, the Vortech controllers and battery backup mid-left, and have room to spare centre and right side.



The stacked sumps. You can see the returns from the overflow going into the sump top left. I hand tightened them and still had a couple leaks. My LFS told me to use a wrench and give them all quarter turn and low and behold they are all good! You can see the abyzz A200 in the primary return chamber.



The lower sump's return manifold is done. The three bulkheads on the bottom sump are for draining the chambers and one is an open emergency drain (far left).



You may be able to just make out the lower drain plumbing. The centre and right bulkheads are on ball valves while the left is a safety to prevent overflowing in a worst case scenario.



I need to clean the 1/2" plywood up a bit more, a little white caulking, etc., but the plywood is in place to allow me to affix electronics, powerhead controls, wiring looms, power bars, really anything I want to... to the wall. The space on the right is for the reactor shelf, dosing containers, profilux, etc.

Reply With Quote
  #134  
Old 10-15-2013, 02:12 AM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

Does anyone have personal experience with the RK2 ozone generators? I am looking at buying their 300mg/hr unit. Also, would you be content using the Profilux system to control and monitor the ORP or would you buy the RK2 monitor controller? I personally feel that the Profilux should do the job just fine, but am open to everyones suggestions!

Cheers,
Scott
Reply With Quote
  #135  
Old 10-15-2013, 02:46 AM
Madreefer's Avatar
Madreefer Madreefer is offline
Member
 
Join Date: Nov 2008
Location: Prince George
Posts: 2,064
Madreefer is on a distinguished road
Default

Very nice build. You've got a pretty sweet skimmer. You won't need to run ozone with it. IMO.
Reply With Quote
  #136  
Old 10-15-2013, 03:08 AM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

I'm running ozone for water clarity, something the skimmer won't really effect (as far as I know).
Reply With Quote
  #137  
Old 10-29-2013, 04:35 PM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

It has begun! Damn is my RODI slow! I have the 100psi booster on there and it's still painfully slow.





Return plumbing is 90% done. I just have to paint the 90's black and glue them in!



Reply With Quote
  #138  
Old 10-29-2013, 04:54 PM
lastlight's Avatar
lastlight lastlight is offline
Gold Member
 
Join Date: Jan 2006
Location: Calgary
Posts: 6,997
lastlight has a spectacular aura aboutlastlight has a spectacular aura aboutlastlight has a spectacular aura about
Default

nice accessible sump off to the side. i loved that about my fish room too. i had always planned to add the fridge but you beat me to it lol. looks great!
__________________
Brett
My 67 392 225 101 94 34 97 404 28 93 209 gallon reef.
Reply With Quote
  #139  
Old 10-29-2013, 06:07 PM
sphelps's Avatar
sphelps sphelps is offline
Member
 
Join Date: May 2006
Location: Lyalta, East of Calgary
Posts: 4,777
sphelps is on a distinguished road
Default

Great job on the plumbing, did that silicone hose come with the pump?
Reply With Quote
  #140  
Old 10-29-2013, 10:05 PM
Scythanith's Avatar
Scythanith Scythanith is offline
Member
 
Join Date: May 2008
Location: Saskatchewan
Posts: 1,088
Scythanith is on a distinguished road
Default

Quote:
Originally Posted by sphelps View Post
Great job on the plumbing, did that silicone hose come with the pump?
Thanks Steve. I had to order the silicone connector kit from Abyzz. The clamps are pretty badass though!
Reply With Quote
Reply

Tags
abyzz, bubble king dc 250, mitras, profilux 3, reef


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 02:32 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.