URGENT HELP NEEDED!!

[Oilers]

I was looking at my tank and I noticed there was some water on the floor. It wasn't much so I thought maybe the fishes have splashed some water out onto the floor. However, when I inspected more closely, I noticed that there was also water at the top of the stand where the bottom of the tank touches. I took some paper towel and wiped everything dry. After an hour or so, I found water in the same place again.
Is my tank leaking? If so, how do I find where it leak? Is it fixable and how do I do that? Is it worth it to fix or should I find a new tank since once the tank leaks, it can leak again in the future. What should I do? HELP!!!

PS A friend of mine told me that the problem might be when I started using the easy blade scraper attachment for the cleaning magnet. The blade might have cut into the silicon that holds the tank together.

[Nano]

Sounds like a leak to me. If its coming from under the tank itself I would suspect a crack or bad caulking. Maybe safe to pick up a holding tank and inspect the tank for cracks or leaks. Sorry bout your luck. That happened to me in my old 40g cichlid tank

[daplatapus]

I get something very similar. But I have an old tank with a cracked plastic rim. When my koralia pumps kick in or my water level gets a bit high capillary action sucks the water up and over the glass (but under the plastic trim) and it dribbles down the front and side panes of my tank. I guess there's either no silicone left in spots of the plastic and the glass and water can flow between them.
How old is your tank? Does it ave a trim on it? Is the plastic trim cracked or chipped anywhere?

[Aquattro]

My tank used to drip from the bottom, but it was from a leaking bulkhead at the top rear. Check all the top edges, and bottom bulk head for leaks or salt build up. If nothing there, you may have a leak and at that point, you might want to pick up a spare tank. You can repair it, but it will take a bit of time to tear it apart, clean it and put it back together, then let it cure for a few days. Depending on size, it might be easier to get a new tank

[Oilers]

Originally Posted by daplatapus

I get something very similar. But I have an old tank with a cracked plastic rim. When my koralia pumps kick in or my water level gets a bit high capillary action sucks the water up and over the glass (but under the plastic trim) and it dribbles down the front and side panes of my tank. I guess there's either no silicone left in spots of the plastic and the glass and water can flow between them.
How old is your tank? Does it ave a trim on it? Is the plastic trim cracked or chipped anywhere?

My tank is over a year old. I think I've found where the water came from. The water is dripping from the top of the tank where the plastic rim is so it's quite similar to what you had before. How did you fix it?

[Oilers]

One more problem,
Since my tank was leaking water, it lets to my ATO reservoir draining at a faster rate than I anticipate it to be. I woke up this morning to an empty reservoir and the lights on the ATO blinking red. I refilled the reservoir and the pump turned itself on but there's no water coming out of the hose. I turned the unit off and shake the pump to get rid of the air bubbles but it still doesn't work. Any idea? I am using a Tunze ATO.

[howdy20012002]

if your reservoir just emptied itself into the system, your salt levels will be low.
I would double check to see where your salinity is sitting
Neal

[Oilers]

Originally Posted by howdy20012002

if your reservoir just emptied itself into the system, your salt levels will be low.
I would double check to see where your salinity is sitting
Neal

It is 1.023. The light on the ATO is now saying the water level in the reservoir is too low even though I just refilled it. So strange.

[Myka]

I run my Tunze Osmolator dry all the time, like twice a week. Just refill and shake the pump up and down while you hang onto the hose. Sometimes it takes a few shakes, or a couple thumps on the bottom of the reservoir.

Originally Posted by Oilers

It is 1.023. The light on the ATO is now saying the water level in the reservoir is too low even though I just refilled it. So strange.

That's pretty low for reef. Reef should be more like 1.025 or 1.026.

[Oilers]

Originally Posted by Myka

I run my Tunze Osmolator dry all the time, like twice a week. Just refill and shake the pump up and down while you hang onto the hose. Sometimes it takes a few shakes, or a couple thumps on the bottom of the reservoir.



That's pretty low for reef. Reef should be more like 1.025 or 1.026.

Thanks Myka. The ATO problem has been resolved. I took the hose connecting the pump off and put it back on. Got rid of the air bubbles I guess. I'll fix the salinity once I get the leak problem solved.