Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > DIY

Reply
 
Thread Tools Display Modes
  #1  
Old 08-30-2012, 07:05 PM
andy8383 andy8383 is offline
Junior Member
 
Join Date: Aug 2012
Location: madison, wi
Posts: 3
andy8383 is on a distinguished road
Default Plywood Tank Build 300 Gallon

Hi All,

After looking through a number of threads on people who have built plywood tanks, I've decided to jump in and give it a shot. I've started to build a 300 gallon plywood tank (8' long, 2.5' tall, 2' deep) with an overflow stretching across the back of the tank. I plan to fiberglass the entire tank and install 1/2" sapphire glass in the front. The tank will be part of a non-profit office redesign I'm spearheading.

I have some experience (used to have a 75 gallon saltwater tank in college), but I have been out of it for a number of years. I know I'm going to need a lot of advice along the way, so I hope more experienced forum users can help give me some direction.

A few quick questions...

- After looking at the various waterproofing options, I've decided to fiberglass the tank (inside and outside - might be a bit overbuilt, but I want this tank to last). I've just started researching the fiberglassing process and it doesn't sound too complicated, but I have zero experience in this. Has anyone fiberglassed a tank before? Any suggestions on type of resin/hardener or where to get them? Any other tips would be very appreciated!

I've attached a few pictures to this post of the plywood being cut and screwed together. It's starting to take shape!

Thanks Everyone!
Attached Images
File Type: jpg IMG_0968.jpg (35.8 KB, 109 views)
File Type: jpg IMG_0971.jpg (23.9 KB, 99 views)
File Type: jpg IMG_0972.jpg (22.9 KB, 95 views)
File Type: jpg IMG_0973.jpg (23.4 KB, 99 views)
Reply With Quote
  #2  
Old 08-30-2012, 07:38 PM
sphelps's Avatar
sphelps sphelps is offline
Member
 
Join Date: May 2006
Location: Lyalta, East of Calgary
Posts: 4,777
sphelps is on a distinguished road
Default

The plywood part looks good so far. I've done some fiberglass stuff before but not a tank. I would guess it's not going to be all that easy to coat the inside of that tank properly nor will it be very cheap. Fiberglass resin is also pretty toxic stuff and don't forget you'll still have to coat the finished fiberglass with some kind of epoxy paint as it can rot. I considered something similar myself at one point but adding up costs pretty much exceeding the cost of glass so it didn't make much sense to me.

You might also want to consider 15mm starphire front rather than 12mm. Personally I think using 12mm will be a mistake as it will have a noticeable bulge. Even a standard 6ft 230 gallon uses 12mm standard and it's pretty noticeable, going up to 8 feet and softer glass will be much worse.
Reply With Quote
  #3  
Old 08-30-2012, 08:05 PM
Cal_stir's Avatar
Cal_stir Cal_stir is offline
Member
 
Join Date: Aug 2010
Location: Corunna, On.
Posts: 647
Cal_stir is on a distinguished road
Default


I will be following as I am planning a build as well, seems that most use West, MAS, or US composites epoxy, some put a final coat of potable epoxy paint while others don't.
__________________
Crap happens, that's why they sell toilet paper in 48 roll packs!
Reply With Quote
  #4  
Old 08-30-2012, 08:06 PM
mike31154's Avatar
mike31154 mike31154 is offline
Member
 
Join Date: Jul 2008
Location: Vernon
Posts: 2,073
mike31154 will become famous soon enough
Default

I know a bit about the fiberglass & epoxy process having built a cedar strip canoe. No clue about plywood tank construction though. The glass epoxy process is indeed not that difficult, but you need a well ventilated area to work in and be prepared to spend a few $$$s on the premium epoxy resin you will need. There are different weights of cloth available, not sure what would be appropriate for a plywood fish tank, but if weight is not an issue, the heavier cloth will add strength.

Various boat building forums & vendors of kits/plans will be a great source of information. My canoe is built from plans produced by Bear Mountain Boats. There's plenty of info there on glassing etc. Along with the plans for the boat I also purchased the book Canoe Craft which provided plenty of guidance with regard to fiberglass/epoxy construction. The epoxy resin I used is the one recommended by many boat builders, the West System. It is pricey but the finish is excellent. With a fish tank you may not be that concerned with the finish on the resin since it will be covered? Hope this helps.
__________________
Mike
77g sumpless SW
DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206
Reply With Quote
  #5  
Old 08-30-2012, 11:21 PM
Cal_stir's Avatar
Cal_stir Cal_stir is offline
Member
 
Join Date: Aug 2010
Location: Corunna, On.
Posts: 647
Cal_stir is on a distinguished road
Default

what thickness plywood are you using and are you gluing and screwing?
__________________
Crap happens, that's why they sell toilet paper in 48 roll packs!
Reply With Quote
  #6  
Old 08-30-2012, 11:26 PM
Aquattro's Avatar
Aquattro Aquattro is offline
Just a guy..
 
Join Date: Aug 2001
Location: Victoria, BC
Posts: 18,053
Aquattro is a jewel in the roughAquattro is a jewel in the roughAquattro is a jewel in the roughAquattro is a jewel in the rough
Default

Check Marc's old thread on his 1000g plywood tank, he might have a few tidbits to offer

http://www.canreef.com/vbulletin/showthread.php?t=31113
__________________
Brad
Reply With Quote
  #7  
Old 08-30-2012, 11:30 PM
andy8383 andy8383 is offline
Junior Member
 
Join Date: Aug 2012
Location: madison, wi
Posts: 3
andy8383 is on a distinguished road
Default

Plywood is 3/4" inch oak. When attaching the pieces of wood together, we glue first and then screw them together. We are going to fiberglass the entire piece as well, but haven't yet.

And thanks for the link to Marc's thread. Already checked it out during the planning stages. Great build and very helpful.
Reply With Quote
  #8  
Old 08-31-2012, 12:39 AM
Edmonton newbie Edmonton newbie is offline
Member
 
Join Date: Mar 2009
Location: edmonton
Posts: 245
Edmonton newbie is on a distinguished road
Default

west system has a great book that explains the glassing process very well, east system is a cheaper knock off that i have been using and is very easy to use plus no need for the super ventilation that you used to need while using resins, I would not think twice about using it in my kitchen
Reply With Quote
  #9  
Old 08-31-2012, 02:45 AM
KevinK KevinK is offline
Member
 
Join Date: Jul 2009
Location: Victoria
Posts: 320
KevinK is on a distinguished road
Default

last year I considered building a plywood tank, and checked pricing here and there for the resin.

I found US composite was by far the cheapest, se below, there price point, with shipping to Victoria and made in the us, so no duty, only the local tax:

1x EPOX-635416 = 10 Gallon kit $490.00

1x set of EPX-P41 $6.75

16 yards of FG-C0738 fiberglass cloth $76.00 = $572.75 + $169.98 shipping = $742.73 total


here is what I put on reefcentral
http://www.reefcentral.com/forums/sh....php?t=2064052

even der wille zur macht used it for reef application
Reply With Quote
  #10  
Old 08-31-2012, 02:52 AM
HaZRaTTy's Avatar
HaZRaTTy HaZRaTTy is offline
Member
 
Join Date: Jul 2011
Location: Edmonton
Posts: 482
HaZRaTTy is on a distinguished road
Default

Quote:
Originally Posted by KevinK View Post
last year I considered building a plywood tank, and checked pricing here and there for the resin.

I found US composite was by far the cheapest, se below, there price point, with shipping to Victoria and made in the us, so no duty, only the local tax:

1x EPOX-635416 = 10 Gallon kit $490.00

1x set of EPX-P41 $6.75

16 yards of FG-C0738 fiberglass cloth $76.00 = $572.75 + $169.98 shipping = $742.73 total


here is what I put on reefcentral
http://www.reefcentral.com/forums/sh....php?t=2064052

even der wille zur macht used it for reef application
I remember seeing on Monster Fish Keepers someone building a Plywood tank for FAR cheaper then this. I haven't done any research into the matter but I remember thinking that, thats fairly inexpensive. You might want to look on that forum and see wha they have to say as there are alot of Plywood builds there. This was more then 2 years ago tho.
Reply With Quote
Reply

Tags
aquarium, diy, fiberglass, plywood, tank


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 12:30 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.