![]() |
#1
|
||||
|
||||
![]() Yesterday i cleaned my bio pellets reactor and got to say i did not like cleaning it so I did some searching for new toy and see this thread
http://reefbuilders.com/2011/10/23/a...in-biopellets/ With the unique way of side spinning pellets, I am curious if it will reduce pellets clogging problem, thus reduce the cleaning part. Your thoughts?
__________________
155 gallon bow front |
#2
|
|||||
|
|||||
![]() I have a Vertex UF-20 with a Mag 5 pump (also run my chiller off the same pump), and it works beautifully. I ramped mine up gradually, but eventually had the full 1000 ml Vertex pellet bag in it, and it was tumbling nicely right to the top. I have been running it now for about 6 months and have never had any pellets clumping or clogging. What's important though, is not to use the sponge filters. Instead I used a mesh both top and bottom.
__________________
Reef Pilot's Undersea Oasis: http://www.canreef.com/vbulletin/sho...d.php?t=102101 Frags FS: http://www.canreef.com/vbulletin/sho...d.php?t=115022 Solutions are easy. The real difficulty lies in discovering the problem. |
#3
|
|||||
|
|||||
![]() I have 3 NextReef MR1 and I imagine its like most other reactors, water flows in threw 2 holes in the bottom. From what I see of these is there is a series of small holes in 4 rows inside where the pellets are. I could easily see this working much better and might just have to modify one of my reactors to give it a go.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#4
|
||||
|
||||
![]() hmm interesting, don't you get clogging with all the mulms got created? I ran mine on deltec fr 509 with no sponge but eventually it will clog up over time.
__________________
155 gallon bow front |
#5
|
||||
|
||||
![]() Quote:
__________________
155 gallon bow front |
#6
|
|||||
|
|||||
![]() I too have 1000 ml in my reactor and have not had them clog up but I am running a 2500 gph pump dedicated on them as well.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#7
|
|||||
|
|||||
![]() Quote:
__________________
225g reef |
#8
|
|||||
|
|||||
![]() I have never had mine clog, and never clean it. The only maintenance is to pour in more pellets when it gets low (about every 3 months).
If your reactor is tumbling properly, there is no mulm. All the bacteria stays with the pellets as they slowly dissolve. I've heard that tumbling too fast is not good either. Also, I use MB7, which seeds the right bacteria for these pellets. And I have never had a cyano problem either, and I use the full 1000 ml bag for my 100 g tank. The trick, I think, is to ramp up slowly, and heavy use of MB7 initially.
__________________
Reef Pilot's Undersea Oasis: http://www.canreef.com/vbulletin/sho...d.php?t=102101 Frags FS: http://www.canreef.com/vbulletin/sho...d.php?t=115022 Solutions are easy. The real difficulty lies in discovering the problem. |
#9
|
||||
|
||||
![]() I bought one of these back in November, but still have not put it online yet. Also with potential tank upgrade, I might just hold it off till then.
Will provide a quick review when I have it up and running.
__________________
150DD mix reef with 90 gal sump and 40gal frag tank purple tang, sohal tang, yellow eye kole tang, fairy wrasse. cleaner wrasse, leopard wrasse, and misc fish. GHL Mitras 6200HV X 2, MP40 X 2, MP60 X 1, tunze 6095 X 2, Vertex RX6 calcium reactor, Bubble King SM250, Aquamaxx bio pellets reactor, Profilux 3 |
#10
|
|||||
|
|||||
![]() Mine ran great for a year in a TLF 500. I have about 500ml in my tank. Just recently the reactor has been fine, but the HOSE is the one clogging. I have this Tee'd off my return with LOTS of flow, but so much mulm builds up in the hose that once it clogged it was continuing to clog daily for a week or 2. I replaced the hose 2 times during this only to have the new hose clog and get cleaned out, swapped direction and it would run for another day. Anyways... to fix it I changed how the TLF used flow so that i could get a better less turbulent turnover. I removed the bottom plate, and since the top plate is attached with a rubber fitting, I directed the bottom of the downspout to the edge of the reactor. This causes everything to turnover in a nice roll, seems to work well. No more clogging
![]() These new reactors seem to do that(just sideways), and the large spout size looks like it would provide enough flow with a smaller pump. My TLF with a MJ1200 wouldn't get anything close to the turnover I wanted because of the small openings, these would probably work well with a MJ since there would be little back pressure.
__________________
My 150 In Wall Build |