![]() |
#71
|
|||||
|
|||||
![]() Not sure if anyone noticed this or commented, but no foam under the tank? Is there a reason? I thought it was always recommended in order to remove possible stress points. Same would go for the sump also, if there is no foam.
__________________
![]() Setup: 180G DT, 105G Refuge (approx. 300lbs LR, 150lbs Aragonite) Hardware: Super Reef Octopus SSS-3000, Tunze ATO, Mag 18 return, 2x MP40W, 2X Koralia 4's Wavemaker Lighting: 5ft Hamilton Belize Sun (2x250W MH, 2X80W T5HO) Type of Aquarium: mixed reef (SPS & LPS) with fish Dosing: Mg, Ca, Alk |
#72
|
|||||
|
|||||
![]() Depends on how the black plastic trim is. If its flush to the bottom, then I would say yes. If it has that gap underneath, then no.
|
#73
|
|||||
|
|||||
![]() Yeah I think her base is trimmed in Plastic.
|
#74
|
|||||
|
|||||
![]() It is trimmed in plastic. I noticed last night that I could actually see a gap between the tank and the wood - hope that's ok. I had read someone's else's thread on the foam and with the trim its not needed.
There is foam under the sump, needs to be trimmed, but right now it covers the entire base of the stand. |
#75
|
|||||
|
|||||
![]() Filling tank with water for leak test! Will start playing with rocks to see how things look for aquascaping, hopefully we're salty by the weekend!
|
#76
|
|||||
|
|||||
![]() I have picked up 80 lbs of live rock, 135 lbs of sand, ato, a heater, and more salt. Got the aquascaping done today, added the sand and am now filling the tank with ro water. My mp40 wet side has been replaced (thanks Dave) and I pulled my skimmer out of my 55, cleaned it (now soaking in vinegar to get the coralline off) and will get it in the sump tomorrow. We have some plumbing mods to do but nothing major. I have 60 lbs of live rock in my 55 that will get added after it cycles but still need approximately 40 lbs more. I also did a water change tonight and added that water.
This is what I'm starting with, is there anything I've missed? Should I add salt as the tank fills or wait? Oh, I also picked up 3 radions, set for lights, just working on how to hang them. Will post pics tomorrow. Thanks Last edited by Coralgurl; 02-06-2012 at 02:48 AM. |
#77
|
|||||
|
|||||
![]() Hey Shenna, i have a better thought on the light hanger for ya, simple clean and easy. i will try to sketch it up tonight & send it to you.
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |
#78
|
|||||
|
|||||
![]() Thanks Greg, I tried sketching something up but it looked crappy! Looking forward to seeing what you've got!
|
#79
|
|||||
|
|||||
![]() Im know that Greg can build you a kisk arse hanger for your radions, but here's what I did....... $70 for a pair or "TEK" legs $60 for a chunk of solid wood(for your size of tank) and a jigsaw.......slap on some of that black spray paint
![]() ![]() ![]() ![]() ![]() ![]()
__________________
260g mixed reef, 105g sump, water blaster 7000 return, Bubble King SM 300 skimmer, Aqua Controller Jr, 4 radions, 3 Tunze 6055s,1 tunze 6065, 2 Vortech MP40s, Vortech MP20, Tunze ATO, GHL SA2 doser, 2 TLF reactors (1 carbon, 1 rowa). http://www.canreef.com/vbulletin/showthread.php?t=50034 . Tank Video here http://www.vimeo.com/2304609 and here http://www.vimeo.com/16591694 |
#80
|
|||||
|
|||||
![]() How's this for an ider?
![]()
__________________
Feed the bear goodies, make a new friend, don't feed the bear............... 8' - 165gal Reef DIY LED's Build 2012 Nano Contest Winner Febuary 2013 POTM Winner 300 gal + 60 gal Complete DIY Build |