Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Reef

Reply
 
Thread Tools Display Modes
  #1  
Old 12-23-2012, 04:59 AM
scherzo's Avatar
scherzo scherzo is offline
Member
 
Join Date: May 2009
Location: Coquitlam
Posts: 243
scherzo is on a distinguished road
Default

Our TDS is pretty low compared to Alberta's. If you're like me in Coquitlam. I get about 5-10 TDS right out of the tap.

Our RO membrane will filter most out and I even have zero going into my DI resin at the last stage. This is after 2 years and about 400-500 gallons.

I do flush often and I also change my carbon and per filter every 5 months or so. I still haven't changed my DI.

We're just lucky.


Quote:
Originally Posted by Reef Pilot View Post
I've heard that, too, but not so sure if that is true. I say that because I run an RO/DI system, and haven't changed out my DI media in over 2 years, and it is still good. Not only do I feed my RO/DI directly to my sump with my own DIY ATO dual float fail/safe system, but I also have 2 pressure storage tanks before the DI (but after the RO) in my system. So I always have about 10g or so of ready RO water, which quickly filters through the DI on demand. We use the RO side for house water in the kitchen too, and those storage tanks always ensure a ready supply for that, too.

My RO membrane is also more than 4 years old, and still working good. I have dual TDS gauges, one after RO (but before DI) and the other measure after RO/DI. However, I have a flush bypass valve (and DI bypass, too), and whenever my TDS from the RO gets over about 2 or 3, I do a flush (about every couple months). After DI, the water tds is still always 0.
Reply With Quote
  #2  
Old 12-23-2012, 01:53 PM
mike31154's Avatar
mike31154 mike31154 is offline
Member
 
Join Date: Jul 2008
Location: Vernon
Posts: 2,073
mike31154 will become famous soon enough
Default

Yep, most of you folks on the coast could probably forget about the RO membrane & run your water straight through DI after a couple of pre filters + carbon, your tap TDS is so low to begin with. All you might need is something to slow down the flow through your DI so it has time to do its thing. Still have to do the math though, cost of DI & how long it lasts without RO stage etc. This way you would not have any waste water as with the RO plumbed in there.
__________________
Mike
77g sumpless SW
DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206

Last edited by mike31154; 12-23-2012 at 01:56 PM.
Reply With Quote
  #3  
Old 12-23-2012, 02:07 PM
Reef Pilot's Avatar
Reef Pilot Reef Pilot is offline
Member
 
Join Date: Nov 2010
Location: Langley BC
Posts: 1,883
Reef Pilot is on a distinguished road
Default

While my tds after DI is always 0, the tds after RO (before DI) will climb to 10 or more if I don't open the bypass valve and flush the membrane. Like I said, I usually do it when I see it climb to a few ppm, and then it is back down to 0 after the flush. Normally, my gauges show 0:0 or 1:0.

The water out of my tap in Langley is about 50 tds normally. However, it must be higher at times (although haven't caught it in a test), because my sediment and carbon filters still need to be changed about every 4 months or so. I can tell when they need changing because my flow slows down, and it takes longer to fill the pressure storage tanks. And I am always amazed at the red/brown sediment in the pre-filters, despite the seemingly clear tap water.

I still don't think fast flow through the DI is a problem though, as I have that with my RO pressure storage tanks. I do agree though, you should have an RO membrane.
__________________
Reef Pilot's Undersea Oasis: http://www.canreef.com/vbulletin/sho...d.php?t=102101
Frags FS: http://www.canreef.com/vbulletin/sho...d.php?t=115022
Solutions are easy. The real difficulty lies in discovering the problem.

Last edited by Reef Pilot; 12-23-2012 at 02:12 PM.
Reply With Quote
  #4  
Old 12-23-2012, 02:44 PM
mike31154's Avatar
mike31154 mike31154 is offline
Member
 
Join Date: Jul 2008
Location: Vernon
Posts: 2,073
mike31154 will become famous soon enough
Default

With TDS 50 at source, DI only would probably not be economical. I've heard some of you on the west coast have TDS 10 or lower though, so it might be an option for those lucky few.
__________________
Mike
77g sumpless SW
DIY 10 watt multi-chip LED build http://www.canreef.com/vbulletin/showthread.php?t=82206
Reply With Quote
  #5  
Old 12-23-2012, 03:26 PM
Reef Pilot's Avatar
Reef Pilot Reef Pilot is offline
Member
 
Join Date: Nov 2010
Location: Langley BC
Posts: 1,883
Reef Pilot is on a distinguished road
Default

Quote:
Originally Posted by mike31154 View Post
With TDS 50 at source, DI only would probably not be economical. I've heard some of you on the west coast have TDS 10 or lower though, so it might be an option for those lucky few.
Just checked my tap water and it is 64 at the moment. Have never seen it at 10 in Langley. I understand they also supplement here with well water (not sure why as we are tied in with the Metro Vancouver water supply).

Back to the OP question, here is some info on DI replacement from the manufacturer of my RO/DI unit.
http://www.airwaterice.com/category/z.2/

I have this unit, but with the 75 gpd membrane. I bought it used and still going strong.
http://www.airwaterice.com/product/1...TDS-Meter.html
__________________
Reef Pilot's Undersea Oasis: http://www.canreef.com/vbulletin/sho...d.php?t=102101
Frags FS: http://www.canreef.com/vbulletin/sho...d.php?t=115022
Solutions are easy. The real difficulty lies in discovering the problem.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 10:09 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.