![]() |
|
Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
![]() So I think I am going to move my sump to the basement, but have no idea what pump I am going to need to replace mine. It will have to pump about 10' up and maybe 60' over or so.
Thanks |
#2
|
||||
|
||||
![]() http://www.reefcentral.com/index.php...oss-calculator
Everything you should need to know...I use this calculator alot. |
#4
|
|||||
|
|||||
![]() Something elso to consider with a total of 70' run is sump size. You'll need to provide sufficient capacity in the sump to collect all the water draining from the pipe when the pump is shut down or if there's a power failure. Otherwise, mini flood.
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build ![]() |
#5
|
||||
|
||||
![]() That pump is going to have to be huge an draw massive wattage to move water that far I wouldn't bother if the closest you. Could get a sump is 70 feet 3-400 watts running 24/7 will be expensive
__________________
250G DD LED SPS R.I.P. 180G LED SPS 80"x36". 300G custom build Owner of Mountain Ridge Heating and Gas Class A gas fitter, HVAC |
#6
|
||||
|
||||
![]() hmm...well since that seems to far, maybe i will put it on the other side of the basement, which would put it about 10-15' over instead of 60'
|
#7
|
||||
|
||||
![]() My sump is in the basement 10 feet up 50 feet across.
Im using a Reeflo barracuda pump this pump is amazing running 1.5 years solid. The valve is turned down more than halfway and i still have too much flow. if your overflow bulkhead is 1 " it could only handle about 900gph flow anyways. |
#8
|
||||
|
||||
![]() Anyone know what would happen if he went 11' up instead of 10'. Then ran the 60" piece at a slightly down ?
|
#9
|
|||||
|
|||||
![]() I didn't think the friction loss on horizontal runs is all that much provided there aren't too many fittings? Just guessing tho, since I haven't run the numbers thru the head loss calculator.
My planned basement sump will be almost directly under the display so probably also around 11 to 12 feet of vertical head. I've purchased a nearly new Panworld NH-150PS & also a previously owned but new looking Poseidon PS4 to move the water. Panworld is a pressure biased pump & will be used in the warmer months while I'd like to use the Poseidon in the winter since I understand they add heat to the water. Although the Poseidon is flow biased rather than for high head pressure applications, I've seen a few threads with folks using them for basement sumps. The Panworld is comparable to Iwaki & Blueline. I think the Poseidon was also sold under the Velocity brand name. Poseidon PS3 is similar to PS4 but pressure biased. By the looks of the flow charts, the loss at the head pressure for both models is close to the same. Will be less than the Panworld, but still ok I think.
__________________
Mike 77g sumpless SW DIY 10 watt multi-chip LED build ![]() Last edited by mike31154; 10-15-2011 at 03:27 PM. |
#10
|
||||
|
||||
![]() Look at the Reeflo pumps, expensive but in my opinion worth every penny when it comes to high head pressure systems.
__________________
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|