Hanging Ati sunpower

[WarDog]

Originally Posted by Ryanerickson

Warren

Ah yes Ryan, thanks! So Tyler IS trying to solicit business right under my nose. Tisk tisk. Bad Tyler!

[iamfrontosa]

I hang my 60" ATI Sunpower off the 18" ceiling. Best decision ever. Very clean look. I think you should go for it and patch it back up when you move. ATI hanging kits comes with butterfly anchors, and that's what I used. Didn't hit the studs. If you have aluminum studs, you probably wouldn't want to damage it.


Get a laser level. Laydown the light flat on top of your tank. Point the level up to the the ceiling and just use a pen to mark where you should drill.

[spit.fire]

Originally Posted by WarDog

Ah yes Ryan, thanks! So Tyler IS trying to solicit business right under my nose. Tisk tisk. Bad Tyler!

Just trying to help a fellow reefer out I am a fabricator and all...

[mike31154]

Originally Posted by Myka

Do it anyway. Then when you move just put a bit of white filler (DAP Alex Plus is good) and no one will be the wiser. Most renters do more damage than a couple of screws in the ceiling.

+1. Surely renters are allowed to hang pictures on the wall, making holes that are repaired when they move. Ceiling should be no different. If possible, use a stud finder to locate something solid to screw into. Drywall anchors for ceilings are available, but not as strong as a rafter or joist. If the light assembly is not that heavy, then no worries really.

[chefpaakk]

Originally Posted by mike31154

+1. Surely renters are allowed to hang pictures on the wall, making holes that are repaired when they move. Ceiling should be no different. If possible, use a stud finder to locate something solid to screw into. Drywall anchors for ceilings are available, but not as strong as a rafter or joist. If the light assembly is not that heavy, then no worries really.

Yeah I get that. I'm am uncertain as to what's past the drywall. The floors are concrete.. Would they put the drywall right up to the concrete or would there be studs too?

Also I know all the studs in the building are the steel studs. They aren't the easiest to find.

[Myka]

Originally Posted by chefpaakk

Yeah I get that. I'm am uncertain as to what's past the drywall. The floors are concrete.. Would they put the drywall right up to the concrete or would there be studs too?

Also I know all the studs in the building are the steel studs. They aren't the easiest to find.

The Drywall ceiling will be off the concrete to leave room for pipes and wiring. They could be wood or steel. If they're steel, use a strong magnet to find them. Stud finders for wood don't work well if you have popcorn ceiling, low profile spackling works better. You can knock and hear the sound change when you're on a wood stud if you have a good ear. You can usually find a stud if you take a look behind a light fixture in the ceiling, and measure 16" on center. Sometimes the studs are 24" on center in condos though.

[Galizio]

Originally Posted by chefpaakk

Yeah I get that. I'm am uncertain as to what's past the drywall. The floors are concrete.. Would they put the drywall right up to the concrete or would there be studs too?



Also I know all the studs in the building are the steel studs. They aren't the easiest to find.

Make sure if are 2x2 or 2x4 steel studs, also be careful cause water pipe and electrical wires are really close to the studs, when they do drywall ceiling on condos they most likely try to save as much space possible so concrete can be just2" past the drywall sometime... If I was you will get an custom hanging kit made... Just my opinion


Sent from my iPhone using Tapatalk

[Myka]

Originally Posted by Galizio

Make sure if are 2x2 or 2x4 steel studs, also be careful cause water pipe and electrical wires are really close to the studs, when they do drywall ceiling on condos they most likely try to save as much space possible so concrete can be just2" past the drywall sometime... If I was you will get an custom hanging kit made... Just my opinion


Sent from my iPhone using Tapatalk

Building code requires those pipes and wires to have protection - usually little steel plates that are mounted on the stud where the lines are.

[Galizio]

Originally Posted by Myka

Building code requires those pipes and wires to have protection - usually little steel plates that are mounted on the stud where the lines are.

Not really, they use steel plate in wood building, on a condo where they use steel studs more likely they just use some plastic rings to make sure the pipes don't touch the steel studs holes, steel plate only get use if the pipes are really really close to the studs, most likely they take in consideration that drywall screw are 1-1/4 ", and believe me , I saw some were steel plate was not used or stuff like that, honestly is a big risk to take, if u flood 10 floor under you....


Sent from my iPhone using Tapatalk

[chefpaakk]

A risk I am not willing to take.. I think I'll stick with my original idea.. I just have to decide if I want to order a fixture stand off ebay/amazon, or if I want to have a custom one done.