![]() |
|
Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
![]() Thanks everybody!
glad to hear my scape is canreef worthy I do however have to secure every frag in the tank still I need some good puddy from somewhere and figure out which type of glue to use for securing the pieces I do have one question, it seems my zoas are a bit agitated, they barely open during the light cycle. What reason could there be to this, plus it is close to WC day so that could contribute. if you have any opinions Im all ears! this would be the revamped stock list and harware list: Stock: Coral: Frogspawn torch GSP Pulsing xenia watermelon zoos purple green acan green hammer rainbow yuma purple yuma green furry mushroom superman shroom orange burst rhodactis inverts: hermits narcissus snail 3 x sexy shrimp (1 m, 2F)... both preggers neon yellow maximini nem fish: firefish cleaner wrasse (pending pick up tuesday hopefully) Hardware: stock PC lighting, 1 X 50/50, 1 X 10k 2 blue leds stock surface skimmer addon, some bioballs for fun till fuge colbalt maxijet1200 return pump biocube 14 skimmer (starting to wonder) filter garbadge consists of, 110ac carbon bag, purigen, some cemipure elite, sponge, and poly fibre (waiting on fuge mod) Last edited by Beano1169; 01-13-2013 at 01:27 AM. |
#2
|
||||
|
||||
![]() ok so everything is going well, but now I have noticed that for that for whatever reason my hydor 360 reflector or my mj1200 is blowing a few small bubbles into the tank. micro bubbles from what I understand are not good for reef envrionments? any suggestions?
|
#3
|
||||
|
||||
![]() On my JBJ12 microbubbles was either low water level, or one time the hose from the pump up to the outlet had a small crack in it where air was sucked in by the passing water.
__________________
Single System Setup: 210G SPS reef, 225G FOWLR, 72G water change, 50G frag, 120G sump. I promise a journal at some point! (anyone need some coral frags? I likely always have stuff that is frag-ready) |
#4
|
||||
|
||||
![]() awesome tahnks for the advice perhaps my hose is cracked at the moment. May I ask if you run a skimmer and if so where is it located? which camber if that is it sits in the back
|
#5
|
||||
|
||||
![]() Yep skimmer -- the Oceanic one, works great for this tank (much better than it does in the oceanic BC 14
![]() All in the photo: Chamber 1: heater, bag of GFO, bag of Carbon Chamber 2: skimmer Chamber 3: chaeto (on a "tray" sitting on top of the pump) Output: Hydor FLO rotating deflector Water level in the back kept at the chamber 2->3 overflow level -- which is good for the chaeto and seems ideal for the skimmer... skimmer makes very thick buildup, not much liquid, which is ideal for such a small system. ![]()
__________________
Single System Setup: 210G SPS reef, 225G FOWLR, 72G water change, 50G frag, 120G sump. I promise a journal at some point! (anyone need some coral frags? I likely always have stuff that is frag-ready) |
#6
|
||||
|
||||
![]() Thanks that helped alot I tried it in C1 but its a bugger to deal with. I am doing my weekly change out tuesday, so I will swap er then haha.
I do have a question for anyone out there who uses Chillers on nano tanks, my tank at night sits at about 79.2 F recently I have discovered, that with the warmer weather if I do not take percautions to close my room door, the tank may get as high as 85.6 F. Im a little worried about this and would like to know the best solution to correct it, I am planning on an LED upgrade with stunnerpros from Modular but until then I need a solution. Thanks for the help everyone, and hope to hear some responses soon. |
![]() |
Thread Tools | |
Display Modes | |
|
|