Greg's 75g

[Nano]

Originally Posted by gregzz4

It's funny how just wanting a clean-looking DT has progressed to such a monster sump build.

Speaking of which I may have missed it, but are you going to try an algae scrubber on this tank? I know Reefwars(Denny) has one, and his tank is super clean, mind you he has a dozen types of macro algae as well lol

[gregzz4]

I'm going to try to avoid a scrubber. I'll try Chaeto and HC GFO to start with. If I need to expand the system, I can move the beer fridge and add another tank.

[Nano]

Originally Posted by gregzz4

I'm going to try to avoid a scrubber. I'll try Chaeto and HC GFO to start with. If I need to expand the system, I can move the beer fridge and add another tank.

I dunno.. the beer fridge is a must IMO

[gregzz4]

Woah there big fella !!!! I didn't say remove. I'm crazy, but not certifiably so
There's room on another wall beside my desk if I get rid of a useless hutch

[gregzz4]

I posted this for lockrookie so thought I may as well add it here in case it inspires someone

[gregzz4]

I went shopping today for a simple check valve for the chaeto system.
For those of you out of the loop, the new system bleeds loads of air into the lines that causes the system to puke loads of water over the sump sides on re-start.

For those of you looking for the short story;
I drove over 70 miles and spent 5 hours to bring home the needed plumbing


For those of you willing to read the long story;
I left home @ 9:30am and drove to Ocean Aquatics. When I got there, I found out they didn't have the 1" clear union swing check valve I wanted, so I bought a 1-1/2" one. I then left Delta and headed for Corix in Coquitlam. Little did I know about how bad the construction delays are on the Fraser River Perimeter Road. It took me an hour and 25 minutes.
OK, no biggie, I've got time today and it's still only 12:30.
I found all the adaptors I needed and got out of there for under $6. Woohoo !
Out to the truck go I and, before I drive away, I decided to test fit a couple fittings in the new valve. To my dismay, the slip fittings fall into the valve. So back into Corix I go and attempt to solve the problem. Sorry, Charlie ....
The new valve was manufactured wrong.
OK .... deep breath ........ ( I need a beer ) .... I have to go back to OA.
I love driving my truck, but I have a tank to finish.
40 mins back to Delta ..... good thing I get great reception ... I forgot my media.
I get back to OA and show bud the issue. Even He's shocked. They had one valve left the same size and, lo and behold, the fittings are correct. I just happened to grab the one in stock that was made wrong.
No biggie, away I go with one that works.
Out the door, into the truck, out the driveway, hmmm ... this valve is too big for my space.
Back to the store, exchange for the only 3/4" one they have, test fit with a 3/4" fitting I have with me, all good.
Hit the road. Hit the ..... Alex Fraser traffic ........ on River Road ..... puddle along for another 1/2 hour.
Alright, I'm in New West, I'll take the Marine Way exit for Burnaby and .... Oh crap, they changed the off-ramp. Now I'm really in New West ... and look at all the cars ............................................
It took me another 1/2 hour to get to Kingsway .... Oh look, a beer store. That'll come in handy in about 15 mins.
I got home @ 2 flippin' 30

I'll post a pic or 2 of the finished plumbing when it's done. I'm still messin' with it and knocking down some liquid prozac

[gregzz4]

Success
The new valve works very well. I am again very happy with my decision to make a change.
There's no more air/draining issues causing a huge mess on pump re-start.
I've turned the pump off/on over the last hour, letting the sump equalize between tests, and it's awesome
Keep in mind ... this change was not done to eleviate back-flow per se, but only to stop air intrusion.
So, forward and onward again to get this little tank salty
Here's the new setup





Ya, Brett, I have become lazy with the cement.
Brett commented on the neat-ness of my first few joints way back when I began. I started off making everything really clean looking, but have, after 50' of pipe and $100s of dollars in glass and fittings, lost my patience and went with 'just glue it, who's gonna see it ?'

[lastlight]

It's ok man I didn't even iron the sheets I hung behind my tank =) Not sure I even have an iron these days actually lol.

I can relate to the air bubbles/splashing. When I bring my water-change section of the sump back online I have to do it really slow. Huge bubbles fly out and the water level is less than an inch from the top of the sump in that compartment. I've 'gone over' many times