![]() |
|
#1
|
|||||
|
|||||
![]() Love the dimensions and love the acrylic!
My only concern (and it's too late now) is the acrylic thickness. Hopefully, it is 1" thick, but that will leave you unable to use the Vortechs which I believe won't work on 1" acrylic. I would bet that a 96" x 30" panel would deflect if it were 3/4" thick. Get some of these large strainers for those intakes. Like these (on the right, NOT like the ones on the left)... These don't clog up or create dangerous suction like the smaller ones do. ![]() These strainers only come in female threaded, so put a female threaded bulkhead in and shorten a threaded nipple so that the strainer fits as snugly as possible against the bulkhead. Have a couple extra so you can just swap them out to clean them. Nice...How many sides are you going to have viewable?...and what are the plans for your fishroom?
__________________
400 gal reef. Established April, 2007. 3 Sequence Dart, RM12-4 skimmer, 2 x OM4Ways, Yellow Tang, Maroon Clown (pair), Blonde Naso Tang, Vlamingi Tang, Foxface Rabbit, Unicorn Tang, 2 Pakistani Butterflies and a few coral gobies My Tank: http://www.canreef.com/vbulletin/showthread.php?t=28436 |
#2
|
|||||
|
|||||
![]() The new MP60 will work on 1" thickness
__________________
There's plenty of room for all God's creatures. Right next to the mashed potatoes. |
#3
|
|||||
|
|||||
![]() I was thinking of the MP60's already.
The tank is 3/4". I asked Tenecor if by switching to 1" I could reduce the size of the bracing, but they said no. It would only give a thicker appearance to the acrylic. For the price (and added weight) it didn't seem worth it. Untamed, I did see those strainers on your tank build and want to get those. You got them from U.S. Plastics, didn't you? This tank is going in my workshop, so the fish room options are pretty much open. No restrictions for height or space. 3 sides viewable, with a blue back. Mitch |
#4
|
|||||
|
|||||
![]() Nice tank, I am suprise you didn't go with 1" acrylic. With that height and width, 3/4" won't give you the piece of mind that 1" would. If you have decided to go this big, why stinch on the most important part.
|
#5
|
|||||
|
|||||
![]() Because Tenecor are the builders and that's what they recommended.
![]() Mitch |
#6
|
|||||
|
|||||
![]() Quote:
__________________
400 gal reef. Established April, 2007. 3 Sequence Dart, RM12-4 skimmer, 2 x OM4Ways, Yellow Tang, Maroon Clown (pair), Blonde Naso Tang, Vlamingi Tang, Foxface Rabbit, Unicorn Tang, 2 Pakistani Butterflies and a few coral gobies My Tank: http://www.canreef.com/vbulletin/showthread.php?t=28436 |
#7
|
|||||
|
|||||
![]() I called Tenecor today, they were just starting on the tank...
A 3/4 tank will deflect 1/4" at the most, and a 1" would be negligible. I told them to go ahead and upgrade to the 1". Thanks for the input. Mitch |
#8
|
|||||
|
|||||
![]() I think that is a good call. My tank is 1" all round. When I'm working in the tank, I lay a plank across the opening and kneel on top of the tank to work. I imagine you'll be able to do that as well, and it is quite handy.
__________________
400 gal reef. Established April, 2007. 3 Sequence Dart, RM12-4 skimmer, 2 x OM4Ways, Yellow Tang, Maroon Clown (pair), Blonde Naso Tang, Vlamingi Tang, Foxface Rabbit, Unicorn Tang, 2 Pakistani Butterflies and a few coral gobies My Tank: http://www.canreef.com/vbulletin/showthread.php?t=28436 |
#9
|
|||||
|
|||||
![]() Just a note of interest regarding acrylic thickness - Today I came across another 600g tank on the net - Dakotareef.
His tank is 120L X 48W X 24H. Made from 1/2" acrylic in 2006. Mitch |
![]() |
Thread Tools | |
Display Modes | |
|
|