Myka's 90 gallon build & 3 province move (Pics Feb 6)

[mike31154]

Ya, my plan is to set up the new tank as a room divider between the kitchen & dining room (sump in the basement) and a 120 might end up being too wide for me as well. I'm going to tear out a piece of L-shaped kitchen counter and build the tank support there... so losing a bunch of counter space, which is really never a good thing in any kitchen, he he.

[mseepman]

For heating up my RO/DI, I bought a reptile heater cord (11W) off Ebay and I plan to figure some way to use it on or near the input cold water line. Haven't figured it out yet but will sometime soon.

[Myka]

Mike, ya counter space is at a premium around here! Room divider tanks are really nice though. I love the wrap around look. Fish tend to be less shy too because they can't really escape, so they get used to it.

Hey Mark, what was the brand of those awesome fans you found? I will need a couple for my tank, and probably another for my sump.

[mike31154]

Originally Posted by mseepman

For heating up my RO/DI, I bought a reptile heater cord (11W) off Ebay and I plan to figure some way to use it on or near the input cold water line. Haven't figured it out yet but will sometime soon.

Sorry if we're getting a little of your tank build topic here Myka, but Mark, I was looking at the cables used to keep your copper pipes from freezing in the winter. They come in quite a few different wattage sizes and may be an option as well. They simply wrap around the copper pipe in areas that are exposed to freezing temperatures. No reason why they couldn't be adapted for use in heating our RO/DI input water. Of course if you have the newer PEX plumbing, I'm not sure they work for that, didn't look that close at the instructions on the packaging.

And Myka, I might still bite the bullet and go for a 120, it's only a few inches wider than a 90 and I like the perimeter of my tank to be free of live rock, allowing for swimming space and easier cleaning of the glass. I also have a yellow tang in my 75 and I'm sure he'd appreciate the extra real estate. Not a fan of stacking rock against the glass at all.

[banditpowdercoat]

Originally Posted by mike31154

Sorry if we're getting a little of your tank build topic here Myka, but Mark, I was looking at the cables used to keep your copper pipes from freezing in the winter. They come in quite a few different wattage sizes and may be an option as well. They simply wrap around the copper pipe in areas that are exposed to freezing temperatures. No reason why they couldn't be adapted for use in heating our RO/DI input water. Of course if you have the newer PEX plumbing, I'm not sure they work for that, didn't look that close at the instructions on the packaging.

And Myka, I might still bite the bullet and go for a 120, it's only a few inches wider than a 90 and I like the perimeter of my tank to be free of live rock, allowing for swimming space and easier cleaning of the glass. I also have a yellow tang in my 75 and I'm sure he'd appreciate the extra real estate. Not a fan of stacking rock against the glass at all.

Heat tape will work fine on PEX, but it is self regulating and only really gets warm when its below freezing out. It's meant to keep the water just above freezing, Normally, heat trace wont heat the water.

[mike31154]

Aha, no controller/thermostat to dial in the temp. Thanks for that bandit.

[mseepman]

Hey Myka,

I always knew that leaving SW would be a mistake for you. It's just too much fun!

As for those fans, if you mean the ones that I plan to put into that nano cooler that I still haven't built, then here is the link: http://www.ncix.com/products/index.p...re=Thermaltake

I've also heard great things on these:
http://www.ncix.com/products/index.p...facture=Noctua

You'll need to cut the wires and re-wire them to a variable voltage resistor with enough mA to run however many you plan to put on the adapter. That way, you can control the speed of the fans and therefore the noise.

I used one of the Silent Cats on my PC and man was it quiet.

Mike, yeah I looked into those pipe heaters but found that they used too much electricity and were pretty un-controllable. This little cord for reptiles only uses 11w and I figure if I use it wrapped around the input line then it just might make the RO a little more efficient.

[Myka]

Thanks for the links Mark! I'm not sure I can DIY the fans like that. I have no clue about electricity.

[mike31154]

Originally Posted by mseepman

Mike, yeah I looked into those pipe heaters but found that they used too much electricity and were pretty un-controllable. This little cord for reptiles only uses 11w and I figure if I use it wrapped around the input line then it just might make the RO a little more efficient.

Thanks Mark. There was a fellow on RC that posted a great idea that's a win win situation with regard to RO/DI production and cooling your tank. Instead of coiling extra RO/DI input line in a warm bucket as Melev suggested, this guy runs a length of his RO/DI input line thru his sump. This warms up the RO/DI input and cools his system water. Not sure how well this would work in our cool climate, but for those running high power lights and using chillers, it might be an option.