Safe epoxy or glue?

[Myka]

So...no one actually ansered the original question. Is there a "generic" 2-part epoxy that is reef safe? I'm building my rock scape soon here, and have already bought some acrylic rod, but I will end up using quite a bit of epoxy as well to help secure the rocks. I haven't tried zip ties before, but I wouldn't mind using zip ties too, but I'm not sure how you guys hide them? At least the acrylic rods are cheap!

[24storm]

My rock work is done with PVC and zip ties and after a few months the zip ties no longer show. Make sure you use the black zip ties.

Keith

Originally Posted by Myka

So...no one actually ansered the original question. Is there a "generic" 2-part epoxy that is reef safe? I'm building my rock scape soon here, and have already bought some acrylic rod, but I will end up using quite a bit of epoxy as well to help secure the rocks. I haven't tried zip ties before, but I wouldn't mind using zip ties too, but I'm not sure how you guys hide them? At least the acrylic rods are cheap!

[Myka]

I'm sure no one else would see the zip ties after awhile, but I know I would, and that would drive me nuts!!

[24storm]

I honestly don't think i can see any

Lights are out so i can't check but i do not recall seeing them at all anymore unless i just don't notice. Tank is now about 16 months old now.

Originally Posted by Myka

I'm sure no one else would see the zip ties after awhile, but I know I would, and that would drive me nuts!!

[fkshiu]

Originally Posted by Myka

I'm sure no one else would see the zip ties after awhile, but I know I would, and that would drive me nuts!!

I don't know about you, but I don't see any visible zip ties in this tank and I know Marc pretty much secured every piece of LR with zip ties: http://www.reefkeeping.com/issues/20...totm/index.php

Anyway, getting back to the OP's question, I've read on RC about a two-part epoxy that's commonly available at hardware stores that is reef safe. It should come up if you do a google search on the RC site and spend a bit of time digging.

[xtreme]

This thread made me decide its a good idea to spend a few extra bucks buying a reef safe epoxy. Not worth the risk for me.

http://www.canreef.com/vbulletin/showthread.php?t=52452

[Myka]

Originally Posted by xtreme

This thread made me decide its a good idea to spend a few extra bucks buying a reef safe epoxy. Not worth the risk for me.

http://www.canreef.com/vbulletin/showthread.php?t=52452

I agree with you on most things. I usually buy reef designed products instead of "generic" stuff, but tanks are so darn expensive, and I have a really hard time justifying the cost of my tanks as it is. So it makes me feel better if I'm thrifty about buying equipment used or DIY or w.h.y. It doesn't make financial sense to spend as much as I do on my tanks at my age.

[dbdavid]

I also agree for rockwork to use zip ties and rods. I also use Super T and the epoxy sticks to firm up and help support the structure. I found that using each glue individually does not provide a strong hold but using them together provides and lot stronger hold. I also use this method for all my frags or placing new corals. It works best if the pieces being glues are dried off first.

Basically you kneed the epoxy together.

Dry off the spots where you want to glue.

Place a generous amount of the Super T on one end.

Put a piece of epoxy over the Super T glue.

Place some more Super T over the epoxy and then put the two pieces together, hold it for a couple of seconds and you are good to go.

While placing a frag underwater you must hold the frag for a little longer. I put a lot more Super T on it than I would if it were dry as it starts to set as soon as it hits the water.

I stay away from the purple coloured epoxy's as it seems to slime up as soon as it hits the water and it takes longer to cure in my experience.

I use the 2 oz Super T Cyanoacrylate from Lee Valley.
http://www.leevalley.com/wood/page.a...at=1,110,42966

I don't want to experiment with the non reef epoxy's so I stick with the Holdfast epoxy.

Hope this helps a little.

Dave

[Myka]

I will try the glue and epoxy combo!!

[i have crabs]

mighty putty shure looks alot like the two littlefishies epoxy to me.
im still scared though but 6 tubes for $30 isnt bad if its ok.
https://www.mightyputty.ca/spark/index.php?tag=os|sm|go
i guess make that $40 after the shipping