What Size Do You Like for Reef Sump in 4x2x2 tank Stand?

[my3kidsdad]

Thank you for your responses. As big as can be installed under the stand. I am thinking of building in such a way as to push the sump into the tank stand from one end, filling the inside area. I will begin learning about filters and such with this info in mind. Thanks again.

[christyf5]

Originally Posted by my3kidsdad

Thank you for your responses. As big as can be installed under the stand. I am thinking of building in such a way as to push the sump into the tank stand from one end, filling the inside area.

Thats exactly what I had to do because of the way my stand was built (before I had even considered a sump when I first started out with a smaller tank). I ended up cutting out one end and shoving the sump in that way. It was pretty tight but I managed to get it in there. The next stand will be built way smrter

[mark]

another vote as big as you can. really, why not?

[dabandit]

My skimmer is 21 inches tall and sticks out of my sump almost a foot...something to consider. Equipment first trust me lol

[my3kidsdad]

Originally Posted by dabandit

My skimmer is 21 inches tall and sticks out of my sump almost a foot...something to consider. Equipment first trust me lol

So you think equipment should be bought first? Then build the sump to fit as best as possible? This could work.

[dabandit]

Originally Posted by my3kidsdad

So you think equipment should be bought first? Then build the sump to fit as best as possible? This could work.

Thats the only way I've had to rebuild twice,another tip dont go by manufacturers dimensions that was the reason for one of my rebuilds. I just bought a new skimmer and built the sump around it,the water level is perfect for my skimmer and doesnt fluctate because of special baffles, and I went with a lower tank to gain better access to my collection cup its a dream to work with trust me equipment first lol

[dabandit]

heres another pointer setup the feed hose for your skimmer run it into a five gallon bucket and time how long it takes to fill,from that you can calculate your pump size. A little underpowered is good,it lets you adjust flow from the skimmer side because if you turn the valve on the pump side down you'll put strain on the pump due to backpressure and prematurelly burn out your pump

[my3kidsdad]

Originally Posted by christyf5

Thats exactly what I had to do because of the way my stand was built (before I had even considered a sump when I first started out with a smaller tank). I ended up cutting out one end and shoving the sump in that way. It was pretty tight but I managed to get it in there. The next stand will be built way smrter

We value all of your opinions. Would you describe what you are thinking about when you say smarter?

[christyf5]

Originally Posted by my3kidsdad

We value all of your opinions. Would you describe what you are thinking about when you say smarter?

Well my dad built this stand and did a fabulous job on it. However the room in the stand doesn't reflect the exterior dimensions. He put some false backing inside (originally it was designed like a bookcase with shelves, I had it oversized for my 48 gallon tank 48"x12"x12". I didn't really think about how versatile the stand needed to be at the time as I was only a year into the hobby, jumped in with not much research on equipment). The stand was built more like a piece of furniture so instead of just putting veneer on the outside to make it pretty, my dad also put veneer on the inside to hide the framing of the stand (it didn't have doors on it back then) which wasted about 2-3" of working space in some spots on the inside. The stand really couldn't be wasted when I upgraded tanks so I took out the shelves and cut a hole through the midsection to accomodate a rubbermaid sump. Eventually an acrylic sump became available which fit but I was limited to only 11.5inches across because of the stand design (4x4s and really heavy materials, I swear an elephant could stand on it easily, maybe even two elephants!).

Here's a pic which might spell it out better, this is the old acrylic sump:




My next stand will have a wider area to work in as finding an 11.5" sump is a real pain in the butt also I'd like to get rid of that brace in the middle but I have no idea how one does that in a wooden stand. I suppose I'll go with a metal stand next time, people seem to have success those ones for "openness" below. I ended up getting a custom tank built for the sump which is 36"x11.5"x16" which is about the maximum I could fit in there, it could have been a bit longer but I wanted to tuck my calcium reactor in the stand as well so I left room for that.


Also:
1)I like internal skimmers, if they overflow, they overflow into your sump, no harm done for your floors. However, I have never had an external skimmer.

2)Not every tank needs a refugium and I think they're more work than they're worth. IMO, they're not for everyone (or me anyways)

3)If the power goes out, a fair amount of water will backsiphon through your return hose. Many people will drill a small hole just above the surface of the water so that the tank won't be drained to the level of the return's entry. This way the siphon is broken and you don't end up overflowing your sump. Always run your sump to a level that can hold the extra water of both the backsiphon and the skimmer in case of a power outage or pump failure. A good way to test this is after getting water in the system, keep the sump level very low and mark it. Drill the hole in the return line just above the level of the tank water. Then shut off your tank and skimmer and watch the sump fill. Then measuring the difference between the two you can find a comfortable level to keep the sump water at.

4). An ATO is an Auto Top-Off system to replace evaporated tank water with fresh water. Many people use a float valve for this. Or you can buy complete systems that work electronically. This way the salinity in your tank is stable and not fluctuating while waiting for you to add topoff water manually (and for larger tanks it can be a gallon or two a day). I have my ATO setup with a rubbermaid reservoir that is hooked up to a float valve in my sump. The reservoir holds about a weeks worth of water so I'm not continually having to make water to replenish it. (you can see in the pic above I used a smaller rubbermaid which wasn't as convenient, I had to fill it every 2 days).

[Captainhemo]

I had similar experiences here. Built my stand way before I had even considered a sump, in the end I had to remove parts of the stand to fit the biggest sump I posibly could.
Try and buy your equipment before building a sump, that way you can custom fit everything as needed. There is no point having a huge skimmer area if you end up with a skimmer with a small footprint, on the other had, if you end up having a larger skimmer, you'll want to make sure you have enough room to fit it in. When you are selecting a skimmer, be sure you have enough vertical clearance in the stand to be able to easily remove the collection cup for cleaning, this was a really big issue for me as there wasn't alot of vertical space inside my stand.. Alot of skimmers are 20"+ and then need a bit more for the removal of the cup, just something to watch for.
As mentiioned a in an earlier post, make your return section as large as possible if you aren't going to be using an ATO. As the rest of the sumps water levels are maintained by baffles or dividers, any evap will cause the water level in the return section to drop, you don't want the pump cavatating/sucking air as water in the system evaporates. I lose about a gallon / day.
You'll also want to leave space for any heaters/probes/ phosban reactors etc etc, lots to consider .
A good site to start at is:
here
HTH