|
|
|
#1
11-11-2009, 04:09 AM
|
||||
|
||||
Dirty IO salt
I used to to use seachem reef salt but the calcium was high so I switche to IO and adjust the ca and mg levels no problem but the salt seems to be really dirty quite a bit of brown sediment in my mixing bucket...... Is this normal for instant ocean or did I just get a rogue bucket??
__________________
250G DD LED SPS R.I.P. 180G LED SPS 80"x36". 300G custom build Owner of Mountain Ridge Heating and Gas Class A gas fitter, HVAC 
|
|
#2
11-11-2009, 04:56 AM
|
|||||
|
|||||
|
Normal
__________________
"We shall dive down through black abysses... and in that lair of the Deep Ones we shall dwell amidst wonder and glory forever." - H.P. Lovecraft Old 120gal Tank Journal New 225gal Tank Journal May 2010 TOTM The 10th Annual Prince George Reef Tank Tour
|
|
#3
11-11-2009, 01:20 PM
|
|||||
|
|||||
|
Some people say this, but in the dozens of buckets that I have used over years I have never had this trouble. Are you usign RO/DI water of 0 tds? i wouldn't say there is any trouble using the salt since others have this occurrence without any issue.
|
|
#4
11-11-2009, 03:53 PM
|
|||||
|
|||||
|
I also have heard this alot but with the 15 buckets I have mixed I have never seen anything left over, just clear water.
Steve
__________________
 *everything said above is just my opinion, and may or may not reflect the views of this BBS, its Operators, and its Members. If cornered on any “opinion” I post I will totally deny having ever said this in a Court of Law…Unless I am the right one*Some strive to be perfect.... I just strive.
|
|
#5
11-11-2009, 03:56 PM
|
|||||
|
|||||
|
Quote:
|
|
#6
11-11-2009, 04:27 PM
|
|||||
|
|||||
|
I have used IO salt for 12 years and every once in while there is residue in the bottom of the bucket after mixing. I have never had a problem using it though. As I was somewhat concerned I add an old Hagen powerhead with a filter attachment to my salt mixing barrel. This has eliminated any concerns.
Tom R
|
|
#8
11-11-2009, 06:12 PM
|
|||||
|
|||||
|
For those of you who have never seen this before. This picture shows the upper water level line in my water change brute trash can. I use an RO/DI system that has always tested between 0-1 tds. I've mixed 2 buckets of Instant Ocean, 2 of Seachem, 1 of H2Ocean and have just started a bucket of Reef Crystals in the can. In the past I used to use one can for only Instant Ocean and another for Seachem, the Instant Ocean can became very dirty while the Seachem stayed relatively clean.
Those of you who have never had this happen, do you use your newly mixed saltwater right away or do you let it sit for a few days? I let mine sit for a week before I use it. 
__________________
"We shall dive down through black abysses... and in that lair of the Deep Ones we shall dwell amidst wonder and glory forever." - H.P. Lovecraft Old 120gal Tank Journal New 225gal Tank Journal May 2010 TOTM The 10th Annual Prince George Reef Tank Tour Last edited by whatcaneyedo; 11-11-2009 at 06:15 PM.
|
|
#9
11-11-2009, 10:53 PM
|
|||||
|
|||||
|
After a water change I refill the tank with RO/DI water and let it sit with a power head turning the water.
About 2 days before I want to do a water change I add the IO salt and a second pump to mix the salt. The next day I test for Ca and Mag. I then calculate the required dosage of Calcium and Magnesium to bring the batch to the right levels. The following day I pump out my sump and replace the water with the now completed 57G mix. I then pump 57G of RO/DI from my water top off tank to fill my mix barrel for the next change. Tom R
|
Linear Mode
