![]() |
|
Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
#11
|
||||
|
||||
![]() That window on the left end of your tank stand position may cause major algae issues when you have the tank set up, if that is the final spot for this epic tank.
Just something to consider. Anthony |
#12
|
|||||
|
|||||
![]() Totally, hear you on the algae Anthony. I'll board that window up and vent out that way... get rid of some of the moisture
![]() |
#13
|
|||||
|
|||||
![]() Is there a beam or concrete wall under that wall the tank is against? Which way are the joists running? Have you reinforced the floor at all?
|
#14
|
|||||
|
|||||
![]() Hey Myka. You bet!
Hence the change in location. Where I initially wanted to put the tank would have meant ripping up half the finished basement below (myself on a budget) for support but this new location is pretty sweet. The tank will be sitting over a crawlspace, between a concrete perimeter wall and a beam underneath about 3 foot away and perpendicular to the joists... I wall also put 8 supports under the joists directly on top of the slab juuuust to be safe. Even with my old 140G rimless, in a 2nd story apartment, I was always worried about vibration and bouncing floorboards. Hate having people over and then having to tell them to not all stand around the tank at once because the floor might break. lol. |
#15
|
|||||
|
|||||
![]() Quote:
![]() Sounds like good planning for the new tank, I'm not sure you need 8 supports though - just a small beam with a support on each end would be good. Or do a pony wall. ![]() |
#16
|
|||||
|
|||||
![]() Soooo...
After spending much time and effort on getting the main panels in place and the main seams siliconed last night, I found a ton of bubbles and irregularities in some key places. More than I'm willing to live with... this is going to be a lot of water and livestock and I just wouldn't be comfortable with bad seams. That's what $150 worth of RTV 108 looks like, don't think it's going back in the tube like that ;p Ah well, I've stripped silicone before. I should be back to square-one in a week or so, assuming the new silicone arrives in good time. I can only get it from the states and then they insist on shipping it as HAZMAT, charging an arm & a leg for duties. Just wish I knew what went wrong? I've built multiple tanks with the black RTV, maybe now I'm just seeing the bubbles for the first time? Maybe it's the time involved with laying the 10ft beads (thought my hand was gonna fall off!), the stuff starts to skin a bit before I can clamp it. Last edited by thebrinc; 09-23-2015 at 12:03 AM. |
#17
|
|||||
|
|||||
![]() Are you using spacers? Why not order a case of Aqueon silicone? Is that RTV stuff stronger or something? I think "a popular aquarium manufacturer" uses that SCS 1200 stuff.
|
#18
|
|||||
|
|||||
![]() Yeah I was using 1/16" spacers... but one got pushed out when we clamped.
The Momentive RTV 100 series is an adhesive, as opposed to the usual silicone which is a sealant, so it has way more tensile strength. With 10 foot seams I want the extra piece of mind and the price difference would have been okay if I didn't have to do the job twice! Anyway, I have the panels apart & in the garage again thanks to some help from a new found friend. Going to try the dremel trick to get the silicone off faster than the razor blade route. |
#19
|
|||||
|
|||||
![]() You're sure that adhesive is reef safe? I've never heard of it. How did you find out about it?
|
#20
|
|||||
|
|||||
![]() Quote:
|
![]() |
Tags |
500g, diy, kahuna, sechelt, sunshine coast |
Thread Tools | |
Display Modes | |
|
|