Canreef Aquatics Bulletin Board  

Go Back   Canreef Aquatics Bulletin Board > General > Product Review and Equipment Forum > Lighting Specific

Reply
 
Thread Tools Display Modes
  #1  
Old 11-23-2016, 02:30 AM
fraz04 fraz04 is offline
Junior Member
 
Join Date: Nov 2016
Location: lumby bc
Posts: 6
fraz04 is on a distinguished road
Default 3 Channel LED light settings!!

Hello Hello! Looking for a little advice and help on this light i have. I bought a used setup recently and it came with this 3 channel LED light. As far as i can tell ch#1 is white (with a few colours), ch#2 is blue, and ch#3 is moon lights. Each channel goes from 0-100%. What i need to know is what % i should have each channel? It looks like the previous owner had it set up 25% white, 50% blue and 50% moon light. its been awhile since i had a tank and the LED's are new to me. I have yet to set up the tank but plan on having soft corals and fish of course. thanks in advance!
Reply With Quote
  #2  
Old 11-23-2016, 03:47 AM
SpongeAl SpongeAl is offline
Junior Member
 
Join Date: Nov 2016
Location: Southern Ontario
Posts: 20
SpongeAl is on a distinguished road
Default

Basically it is a combination of what you like the look of and what doesn't bleach your corals lol.

Typically you find a balance of blue to white you like, and slowly ramp up the brightness till your coral bleach then turn it back down a bit lol.

Generally speaking a 70/30 ratio of white to blue might be a good starting point, increase the blue for more florescence, increase the white to reduce a monochrome Windex look.

The moon light I don't know, depends what colour it is, you'll just have to try it, usually they aren't bright enough to make a visible difference with the main lights though. If it is noticeably bright, then again just adjust it to taste to start with.

Even when LEDs are dimmed, they are full power in bursts, that is why they bleach coral so easy so be careful. If possible, it might work better to leave the LEDs at as close to full power as possible, then adjust brightness by moving the fixture up and down.

All in all, the white channel is the main sorta wide spectrum light that will give you the growth, while the blue is added for looks for the most part.

Assuming the moonlight is white and of equal strength, the previous owner was running a 60/40 white/blue ratio which should give a result somewhere in the 14K to 20K spectrum, every light is a little different.
Reply With Quote
  #3  
Old 11-23-2016, 05:09 AM
fraz04 fraz04 is offline
Junior Member
 
Join Date: Nov 2016
Location: lumby bc
Posts: 6
fraz04 is on a distinguished road
Default

ok thank you for the info. i wasnt to sure how the LED lights worked but now i'm understanding a little more about them. thanks again.
Reply With Quote
  #4  
Old 11-23-2016, 05:42 AM
e46er e46er is offline
Member
 
Join Date: Nov 2008
Location: Maple Ridge
Posts: 819
e46er is on a distinguished road
Default

My evergrows slowly ramp up throughout the day peaking at 55w/60blue
It took a while to get there tho I started st I think 40/40 and corals started to bleach pretty quickly so I set them at like 20/20 and went up 5%every couple weeks
__________________
250G DD LED SPS R.I.P.
180G LED SPS
80"x36". 300G custom build

Owner of Mountain Ridge Heating and Gas
Class A gas fitter, HVAC
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 01:30 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.