Fish tank in condo

[lorenz0]

So I decided to get a larger tank for my condo but I am in need of some advice

My building is 6 years old and it has a wood frame structure. I am on the 2nd floor and I am a bit worried about weight, last thing I need is to get a phone call that my neighbor below me has a newly acquired fish tank. I have no idea how the support beams run, I emailed the condo board asking for more info and how much dead weight one spot can take. Now where I want the tank I highly doubt its a load bearing wall (separates my room and the rest of the apartment).

I want a 60" long tank to fill the void where my tv used to be. So without having to big of a tank and now worrying the dimensions I have come up with is 60x16x16 and I have calculated it at about 850-900 pounds once everything is in it, including sump and ATO tank.

The cube I have now weights about 400-450 but it is on a load bearing wall. but it is only being distributed on a 30x20 surface area.

Think I will be ok? planning on putting a DP on the tank late this month but I need some peace of mind first

[intarsiabox]

The best advice I can give you is to check with your condo board first.

[Harpo]

Originally Posted by intarsiabox

The best advice I can give you is to check with your condo board first.

I second that motion!

[lorenz0]

Email has been sent out, just waiting to see what they have to say

[steve fedyk]

Most newer buildings are designed to hold 250 lbs per square foot, anywhere on the floor. If your wall you wont to put the tank on the outside of your place you should have no problems. Most condos are the same floor plan up and down, so if you put it next to the wall there should be a wall right below your wall.
If you build your own stand line it with rubber to catch any spills. Thats what I did and work pretty good.

[lorenz0]

Thanks, thats exactly what I have been thinking.

This system will be set up identical to my 60gal, in over 2 years I never had a flood. Only thing I need to consider is the volume of water that is in my overflow and making sure that it will fit into my sump once the pump turns off. Will be installing a check valve on the return again. And of course buying insurance this time. But I like the liner Idea, could always seal the bottom just in case though.

But I have been thinking tonight and might bump it down a foot to being another 48" long tank. Which will drop the weight down by about 150 pounds of dead weight. Plus t5 bulbs are more accessible

[sphelps]

Originally Posted by steve fedyk

Most newer buildings are designed to hold 250 lbs per square foot, anywhere on the floor. If your wall you wont to put the tank on the outside of your place you should have no problems. Most condos are the same floor plan up and down, so if you put it next to the wall there should be a wall right below your wall.
If you build your own stand line it with rubber to catch any spills. Thats what I did and work pretty good.

Not sure if that's accurate, as far I know the typical load limits for residential is 40lbs/sqft. But this is based on room size, so if the room is 10' x 10' then it can safely support up to 4000lbs total. This is typically just a rule of thumb and more for the upper limit you should never exceed. For something more accurate you need to know the type, size, spacing and span of the floor joists as well as how they are supported. However a tank that size won't be a problem. If it was me I would also secure the stand into the wall at half load even if it's not load bearing, this will help distribute the load better.

[spawn]

Dude where in the hell did your T.V. go? The R.P. is now kickin Ass. Thanks again.

Originally Posted by lorenz0

So I decided to get a larger tank for my condo but I am in need of some advice

My building is 6 years old and it has a wood frame structure. I am on the 2nd floor and I am a bit worried about weight, last thing I need is to get a phone call that my neighbor below me has a newly acquired fish tank. I have no idea how the support beams run, I emailed the condo board asking for more info and how much dead weight one spot can take. Now where I want the tank I highly doubt its a load bearing wall (separates my room and the rest of the apartment).

I want a 60" long tank to fill the void where my tv used to be. So without having to big of a tank and now worrying the dimensions I have come up with is 60x16x16 and I have calculated it at about 850-900 pounds once everything is in it, including sump and ATO tank.

The cube I have now weights about 400-450 but it is on a load bearing wall. but it is only being distributed on a 30x20 surface area.

Think I will be ok? planning on putting a DP on the tank late this month but I need some peace of mind first