Help with brakes in BC! :(

[andsoitgoes]

So - we need to replace the front pads and machine the rotors for our 2004 sienna, and I'm trying to find a combo between cost and quality - Does anyone know somewhere reliable but reasonable in the Fraser Valley??

Any help would be greatly appreciated, I've been quoted at about 230 to replace pads and machine the rotors, I know that's not too expensive, but we're trying to put money toward other things (like a house )

Thanks in advance all!!

[Phanman]

if you can find a friend to change the pads its quite easy $25ish for a set of pads, or do it yourself. then machining the rotors are usually like $80 which you will need to do at a shop. Just remember to bleed the brake if you open it up

[BMW Rider]

$230 is pretty reasonable. Aside from DIY, I doubt its going to get much cheaper. Good quality metalic pads for almost anything will run from $50 - $150. Sometimes machining rotors is false economy too. Most have such minimal material that once machined they are at the minimum thickness and become quite prone to warping. You may want to jsut price out replacements which are often not much more than the cost of machining.

[Ticketyboo]

Give me a shout if you need help changing the pads, i can also look at the rotors and if they do need machining, just nip to the local store to have them machined... no need to machine them just for the sakes of it... i find alot of garages charge for this and the rotors really dont need them.

[fishmaster]

Originally Posted by Ticketyboo

Give me a shout if you need help changing the pads, i can also look at the rotors and if they do need machining, just nip to the local store to have them machined... no need to machine them just for the sakes of it... i find alot of garages charge for this and the rotors really dont need them.

Exactly. If the pads are not worn down to metal(making grinding or squeeling noise), they likely dont need turning. If they're smooth, and don't have any obvious grooves in them or are not warped, they're fine. I changed my own brakes in my old bronco many times and didn't often need to machine the rotors. Every brake shop will want to machine or replace your rotors because they want your money. That being said, if you are unsure of what you are looking at, make sure someone who does(ticketyboo perhaps) helps you.
Shaun.

[andsoitgoes]

Originally Posted by fishmaster

Exactly. If the pads are not worn down to metal(making grinding or squeeling noise), they likely dont need turning. If they're smooth, and don't have any obvious grooves in them or are not warped, they're fine. I changed my own brakes in my old bronco many times and didn't often need to machine the rotors. Every brake shop will want to machine or replace your rotors because they want your money. That being said, if you are unsure of what you are looking at, make sure someone who does(ticketyboo perhaps) helps you.
Shaun.

Unfortunately it's down to metal on metal - and has been for a week or so. It's pretty rough - we thought it was a mechanical issue, but nein.

From here on out though I'm going to get the pads and do it regularly, I'm just concerned that we've already gone through one set within 42k - seems a bit off, but it might just be my experience, who knows. Back breaks are at 70% still

I think I'm going to just have Toyota do the works and toss in a clean/reseat of the rear brakes, 305 for everything and then I have the security. I'd be more akin to DIY if my girls weren't involved - but since they are, that is where my concern lies...

[Murminator]

Originally Posted by fishmaster

Exactly. If the pads are not worn down to metal(making grinding or squeeling noise), they likely dont need turning. If they're smooth, and don't have any obvious grooves in them or are not warped, they're fine. I changed my own brakes in my old bronco many times and didn't often need to machine the rotors. Every brake shop will want to machine or replace your rotors because they want your money. That being said, if you are unsure of what you are looking at, make sure someone who does(ticketyboo perhaps) helps you.
Shaun.

This is what I do also

[demon666]

230 is really cheap i payed 850 to have mine done..... but i replaced the callapers too

[fishmaster]

Originally Posted by demon666

230 is really cheap i payed 850 to have mine done..... but i replaced the callapers too

$850 for a sienna? Or $850 for an 1 tonne dully deisel oil riggin type truck?