|
Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Aptasia..... Ro & Di Resin ???????
Will Aptasia die injecting hot vinegar into it anywhere or does it have to be in a specific place?
I have found several of the little fu....s on the rock my toadstool is stuck to & there are no peppermints around . I am going away for a few weeks & nobody else will hardly even look at the tank so i would like to do what I can before Mon. In regards to Ro does it make any difference if the membrane is mounted verticle or horizontal ? where is the best place to get DI Resin. I am in kamloops but haven't been able to find it locally yet. Is there much of a difference between brands if so what is the one I should get? & finally should this substrate go in the trash ? my phosphates are off the chart. I recently bought my first sw set up used it has been running for years. However learning as i go i realize now the previuos owner was creating tons of phosphate from feeding habits & no water changes. The tank looked fine at first to this freshwater guy. However the sps are dull & not doing very well . I am planning on siphoning all of the substrate out tonight to try 7 reduce the phosphate. I dont have a reactor yet. I'm just using some of the fluval bagged crap till I get set up correctly. Here is a pic of the crush on the bottom of the tank. It looks like gravel in the pic? but it is not . I was given advise to get some argonite sand does it matter if it's live or dry? the rock is established already. Ok Ok I will shut up & post this now I could ask questions for days & still be lost Lol |
#2
|
|||||
|
|||||
that looks like fw aquarium gravel. Should go away.
Give the aiptasia a shot in the morning with your choice of killer juice right in the mouth works the best. get a reactor with GFO and the phosphates will go away
__________________
225gal dt with 100g sump. Mitras, vortechs, bubble king, AI Sol and Profilux. http://www.canreef.com/vbulletin/sho...threadid=84782 Will trade subs for frags My other summer hobby: http://www.edkra.ca |
#3
|
||||
|
||||
aptasia
use a syringe with a needle to inject them.i usually use lemon juice,but i guess any type of acid would do-do not inject more than 10 a day -try to keep the acid down in the tank.you can also mix up a kalkwasser paste and smother them-making sure you cover the base as that is where the daughter cells are.and do it in the daytime-not at night as this would release the daughter cells .worse comes to worse and they do spread i can sell you some berghia to take care of the aptasia.
the membrane doesn't matter which way it's mounted-mine is horizontal . a reactor will only keep your phosphates stable-not lower them.if you can ,build yourself an algae scrubber.i've had mine running for 4 days now and it has lowered my phosphate to .17 ppm from .28 ppm and my nitrites from 90 ppb to 64 ppb. try a pool sales and service for the resin |
#4
|
|||||
|
|||||
I say morning because I like to see what I'm doing, do it right when the lights turn on.
Gfo does remove phosphates not stabilize the levels.
__________________
225gal dt with 100g sump. Mitras, vortechs, bubble king, AI Sol and Profilux. http://www.canreef.com/vbulletin/sho...threadid=84782 Will trade subs for frags My other summer hobby: http://www.edkra.ca |
#5
|
||||
|
||||
I think moncous is kinda right on not using phosphate remover. Your better off doing relatively cheap water changes and isolating the problem then using expensive chemicals. I would remove that substrate. It looks the the finer version of crushed coral. Not ideal for long term use without vacuuming.
|
#6
|
||||
|
||||
Thanx for the info everyone.
|
Thread Tools | |
Display Modes | |
|
|