Tank Build - Bad News

[philg3]

Got some bad news from the glass shop working on my aquarium.

I dont have any pics, so paint will have to do while im at work.

While making the notch cut for an external overflow box, the glass cracked and went lower than the 3/4" that i had planned. Now it almost steps down another 3/4" which makes the overflow 1.5" deep and not uniform in shape, ie:

Notch Overflow Fail.jpg

What are your guys thoughts?

Silicone something along the overflow edge raise the bottom part to where i had planned?

What if i added a piece of black acrylic (similar to what standard internal overflows are usually made of) the correct shape and dimensions and just siliconed it to cover the entire back wall? do the same thing with a thin peice of glass?

The plan was to drill two 3/4" holes for the return in the back panel as well as add eurobracing to the top.

The overflow would probably function fine as is, but the water level would be lower than i wanted and every time i looked at it i would know its wrong, not to mention some loss of surface skimming.

What do you guys think of these solutions, and does anyone have any better ideas?

[MarkoD]

make an acrylic overlay with teeth and glue it on at the height you want.

[lastlight]

My suggestion is get what you agreed to. Doesn't sounds like it's your problem unless I'm missing something here.

[philg3]

Wasnt a new tank build, the glass shop was making the cut in an existing Oceanic tank i picked up on craigslist. I figured the glass shop would be better equipped to make the notch opposed to me doing it myself.

I had a discussion with the guy before working on it, and i agreed that i wouldnt blame him if the notch didnt go as planned.

[Blom]

That would be like a mechanic telling me its not his fault if my brakes dont work....

[Money pit]

Originally Posted by Blom

That would be like a mechanic telling me its not his fault if my brakes dont work....

Not even close. Glass breaks in glass shops quite often, its part of the business. The shop warned of the risk, and it was accepted.
MarkoD has a good idea with the acrylic.

[StirCrazy]

Originally Posted by philg3

Wasnt a new tank build, the glass shop was making the cut in an existing Oceanic tank i picked up on craigslist. I figured the glass shop would be better equipped to make the notch opposed to me doing it myself.

I had a discussion with the guy before working on it, and i agreed that i wouldnt blame him if the notch didnt go as planned.

ok what you could do if it is too deep is ask them to make a new pannel to the original spec. then just replace the pannel of glass. I had to do this on a tank I broke when moving.

Steve

[StirCrazy]

Originally Posted by philg3

Got some bad news from the glass shop working on my aquarium.

I dont have any pics, so paint will have to do while im at work.

While making the notch cut for an external overflow box, the glass cracked and went lower than the 3/4" that i had planned. Now it almost steps down another 3/4" which makes the overflow 1.5" deep and not uniform in shape, ie:

my thoughts.. how did you order this? did you supply the glass and have them notch it or are you buying a finnished product? if you supplied the glass and it cracked then yes you have to make due but if you phone up and go a quote on a chunk of glass cut to your spec, then they need to fufill the order and there mistake is on them, not you.

in my opinion 1.5" is hugeand unless you realy crank up the flow you are only going to have 1/4" of water above that. to me gluing a chunk of plastic or glass on the inside is just going to be ugly, but that is my opinion.. see what it would cost for a new pane of glass with the notch, then decide which way.. mind you if it is a big chunk could be expensive so that might make up your mind right there. but it would also give you the opertunity to go to a bigger glass thickness which would reduce the chance of breakage due to the cutout.

Steve

[lastlight]

Originally Posted by StirCrazy

if you supplied the glass and it cracked then yes you have to make due but if you phone up and go a quote on a chunk of glass cut to your spec, then they need to fufill the order and there mistake is on them, not you.

Yeah he's outta luck Steve I had asked him that already:

Originally Posted by philg3

Wasnt a new tank build, the glass shop was making the cut in an existing Oceanic tank i picked up on craigslist. I figured the glass shop would be better equipped to make the notch opposed to me doing it myself.

I had a discussion with the guy before working on it, and i agreed that i wouldnt blame him if the notch didnt go as planned.

Still sucks tho. Rounded corners would certainly be better too. It seems pretty common for shops to use circular bits for the corners and then to cut the horizontal out. Sharp turns are a weak point too but at least this is not a high-pressure area... silicone and acrylic will be strong enough.

[abcha0s]

When we cut glass, it doesn't always work out as planned. There are some cuts that are so complicated that we have to take them to a professional glass cutter. The best example of this is our one piece euro bracing. Part of the cost of these cuts is the risk that the glass will break. If it does break, the glass cutter will redo the cut, but we have to supply the replacement glass. There is also considerable over cuts on a one piece euro needed by the machines while working on the center cuts.

The point is, glass breaks. We assume the risk when building a tank, but would never do so on a prebuilt tank. Part of calculating the cost of a custom tank is the risk of breakage. We have lost money on tank builds due to inaccurate cuts, scratches and breaks.

Nonetheless, I think a 1.5 inch overflow will work fine. If you put a wave box in the tank, it's pretty close to ideal.

- Brad