![]() |
|
Portal | PhotoPost Gallery | Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
|
#1
|
|||||
|
|||||
![]() [rant]
So here I am puttering around my tank today trying to get the stupid bulkheads to quit leaking so I can finally get my sump running. I had them fairly loose since I'm paranoid about cracking the glass, so of course they leak, and need to be tightened up more. I am such a procrastinator. I am tightening up the last bulkhead and CRACK. There goes the sump. ![]() SO I siliconed the crack thinking that would prob do the trick since the crack is only about 3" long, and 3 hours later I am messing around in my planted fw tank and I hear CRACK. Another crack splits up the other side of that bulkhead. Oh for hell... Now I have to go buy a new sump, reinstall the baffles, drill the holes for the bulkheads, buy a bunch of new plumbing pieces, and basically redo the entire thing since I can't get the plumbing apart to repair it. I'm ready to kick the sump. [/end rant] Last edited by Myka; 07-18-2009 at 11:41 PM. |
#2
|
|||||
|
|||||
![]() don't, you might crack it.....
__________________
Brad |
#3
|
||||
|
||||
![]() I have some nice adjectives you can use if you would like to borrow some.
|
#4
|
|||||
|
|||||
![]() How thick is the glass?
|
#5
|
|||||
|
|||||
![]() Thanks for condolences guys.
![]() ![]() I've never used silicone on a bulkhead...maybe I should. It's a standard 15 gallon...it's uber thin. I haven't cracked the 5.5 yet though, and it's even thinner! ![]() |
#6
|
||||
|
||||
![]() bulkheads are pressure fit. use adjustable wrench after hand tightening turn 1/4inch with wrench check for leaks.dan
|
#7
|
|||||
|
|||||
![]() Aw, sorry to hear about your troubles Mindy.....I always hand tighten then a 1/4 turn with a wrench...no silicone
__________________
260g mixed reef, 105g sump, water blaster 7000 return, Bubble King SM 300 skimmer, Aqua Controller Jr, 4 radions, 3 Tunze 6055s,1 tunze 6065, 2 Vortech MP40s, Vortech MP20, Tunze ATO, GHL SA2 doser, 2 TLF reactors (1 carbon, 1 rowa). http://www.canreef.com/vbulletin/showthread.php?t=50034 . Tank Video here http://www.vimeo.com/2304609 and here http://www.vimeo.com/16591694 |
#8
|
|||||
|
|||||
![]() Not sure if you used silicone or not but I always have and never had a leak and I just tighten them hand tight. Just make sure you inspect the bulkhead first because small bumpy casting flaws can cause problems if you don't take them off with a utility knife first.
|
#9
|
|||||
|
|||||
![]() for years i just snug them up and coat the heck out of them with sillicone, and just expect that it will be a pain if they ever have to get removed
__________________
but what the heck do i know |
#10
|
|||||
|
|||||
![]() I feel your pain. Been there, done that. Sucks bad. I too silicone them up now.
|
![]() |
Thread Tools | |
Display Modes | |
|
|