Quote:
Originally Posted by Reef Pilot
Yes, and by offline, I do mean your bucket. That is a pretty tight loop, so water would still be O2 starved even with your koralia. And the presence of all that mulm/muck build-up could be trapped or dying carbon and nitrate laden bacteria, that isn't being flushed out into your skimmer.
And after you put it back online with your tank, the mulm/muck probably continued to build inside your reactor because your outlet was partially plugged.
|
It's possible, but I'm ok with agreeing to disagree. That happened long before I had any of the issues we've chatted about with the reactor. It was before I treated with chemilean or dosed any MB7. At that point I had never seen any mulm of any kind in my reactor, and the effluent line flowed freely with barely any biofilm in it. It had been that way for almost 2 years, and I checked regularly. I wasn't kidding about how pronounced of an effect MB7 had on the system overall, only the 'effect' was the production of copious amounts of equipment wrecking, filter sock clogging goo (It would start overflowing after about 8 hours instead of 24), not really anything I would have considered beneficial.
That bucket also would have been rapidly depleted of any nitrate it contained, so over those 5 days mulm production would have been practically non-existent. I noticed a little bit of detritus in the bottom when I emptied it out, but only because I was looking for it. I suppose it's possible the O2 levels still fell, but certainly not low enough to produce a rotten egg smell. Maybe that means my reactor wasn't actually working at that point and that's why my cyano problem was so bad?
I only started seeing mulm and clumping inside the rector after MB7, and that was after the bucket thing. It wasn't until after I finished the two week start-up dose that I started having problems with the effluent line clogging. After it clogged the first time (I caught it before the reactor went rotten), I had to remove and blow-out the effluent line every couple of days. I eventually started filling it with bleach in my sink, which bought me about a week before it was completely clogged again. Before MB7, it was set and forget. After MB7, it needed daily attention and completely melted down when I didn't have any to give for five days.
Quote:
Originally Posted by Reef Pilot
I may have missed it in all your posts. But does your reactor effluent go directly to your skimmer input?
|
Yup. When it was the super small flexible tubing, it sat right inside the intake pipe of my skimmer. After I modified it, I had the effluent pipe directly above the intake pipe. It probably allowed for a lot more bypass that way, but it was the best I could do at the time. I actually just picked up the parts to build an intake manifold that forces the effluent in to the skimmer, but my pellet reactor is currently sitting in my kitchen sink awaiting disassembly and storage so I'll never get to use it...
Quote:
Originally Posted by Reef Pilot
Despite all that, I am not saying either that was the direct cause of your current problems with your SPS dying. But it may have started the ball rolling, and caused other things to get out of whack. If your ammonia is high, though, sure does seem like a mini crash happening...
Again, I would do massive water changes. And keep that bio pellet reactor offline until everything stabilizes. Then you can start again with getting your nutrients under control, but this time, do things slowly and gradually, and watch your tank and corals closely to see how they are reacting.
If you look at the beginning of my tank journal, I started with a 100 ppm nitrate tank, with very high phosphates (after inheriting a 10 year running tank). It took me a year or more before I finally got everything under control. But has been running clean (zero nitrates and near zero phosphates) for a couple years now, and growing SPS like crazy.
I know your tank was looking great with all your SPS before, too. So with a bit of patience, I am sure you can do it again.
|
yes to all of this, only that I'm not going to go back to pellets. They worked great for me for almost two years, but literally all of this started because I was trying to fix an out of control cyano problem. Experience and research suggest that was directly exacerbated by the pellets, so pretty much everything I've done and all the damage that's taken place has been the result of me trying to treat a symptom while desperately trying to hold on to the source. Why I never had it before, or why it started when it did, or why some people manage to escape it, I don't know, but once it got started it was unstoppable. Since the corals have started dying again, a few more patches have shown up - mostly on dead skeletons (both fresh and old, I think they harvest phosphate directly from the skeleton), so going back to the pellets now seems like trying to put out a fire with gasoline. I still believe pellets can work, but for whatever reason they stopped working for me. I just wish it didn't take losing thousands of dollars of coral to figure that out. I'm not sure what I'm going to do about nitrates in the future, but if it's organic carbon it will probably be 5% vinegar added by a doser.
At least this way I can light the fuge chamber of my sump again and start stocking it with macro algaes. I didn't want the light spill-over hitting the reactor, so it's been dark fuge.