Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Tank Journal (http://www.canreef.com/vbulletin/forumdisplay.php?f=18)
-   -   LoJack's 144 Gallon Reef (http://www.canreef.com/vbulletin/showthread.php?t=96736)

LoJack 04-12-2013 09:09 PM

LoJack's 144 Gallon Reef
 
Well I figured since I did an intro thread and promised a Journal ages ago ... its time to give you folks some photos.

I've been poking around on this forum but haven't been overly active up to this point. I've been making lots of changes to my reef though, and figure its time to document them.

It won't be as jammed pack as my original thread on my local forum ... but thats only because there are now too many photos to sift through lol.

So I guess I'll start with the details.

Thank tank is a custom built, starphire front with black silicone, Euro braced tank with a coast to coast overflow and Beananimal standpipes.

Lets just get to the photos ... I know thats what everyone is going to want anyway lol

LoJack 04-12-2013 09:31 PM

The DIY Stand. I built the frame of the stand out of 2x6 lumber to prevent the need for a center brace.

http://i165.photobucket.com/albums/u...9/ea81d723.jpg

Just basic good one side plywood for the top and the inside bottom since you weren't going to see it anyway.

http://i165.photobucket.com/albums/u...9/3933d4cb.jpg

Then I assembled the face frames. I originally wanted to build my stand out of maple, however I live in Thompson and you can't be overly picky here. Red oak was available, so Red Oak is what I ended up going with.

http://i165.photobucket.com/albums/u...9/3591cb8d.jpg

Once I had the face frames completed, I began building up some pillars to add some 3D depth to the stand. This was going to be a show tank, so I had to adventure out a little further with my woodworking ability and try and a few new things.

http://i165.photobucket.com/albums/u...9/932abc72.jpg

This photo shows a little better how I built up the pillars

http://i165.photobucket.com/albums/u...9/3fd29171.jpg

And the look of the stand before I added any of the trim

http://i165.photobucket.com/albums/u...9/ae4c10c0.jpg

http://i165.photobucket.com/albums/u...9/7d493a6c.jpg

The Rail cap that I built for the top edge of the stand could not be purchased, so I got creative with some oak and my router and made it myself. The trim that you see on the bottom of the stand is actually purchased, its the only trim I was able to buy rather than make. Its a standard 3 1/2" oak baseboard for your walls.

http://i165.photobucket.com/albums/u...9/IMG_2369.jpg

This photo shows the assembly of the rail cap. I designed it so that no end grain would show through when everything is finished. End Grain stains darker than everything else, and I didn't want that to happen on this build.

http://i165.photobucket.com/albums/u...9/IMG_2371.jpg

Then I cut pieces of oak to fill the tops of the built up material at the tops of the pillars.

http://i165.photobucket.com/albums/u...9/IMG_2374.jpg

a 3/4" cove bit and 1/2" 3step bit allowed me to make the trim that finished off the pillars. Here is a close up that shows each of those in one shot. The baseboard on the bottom, the cove that hides the mitres, and the step to provide a smoother transition inside of the pillars.

http://i165.photobucket.com/albums/u...9/IMG_2390.jpg

http://i165.photobucket.com/albums/u...9/IMG_2391.jpg

Then came the stain. I went with a water based Mahogany and 3 coats of water based Poly.

http://i165.photobucket.com/albums/u...9/b7e17f2e.jpg

http://i165.photobucket.com/albums/u...9/28c26c79.jpg

http://i165.photobucket.com/albums/u...9/0b43e3d1.jpg

The Canopy was built in a very similar fashion so I won't bother with build photo's. here it is before stain and doors.

http://i165.photobucket.com/albums/u...9/0c4a6361.jpg

With the stain applied. I also painted the inside white with a high gloss acrylic paint. This will help to reflect more light than a dark interior would, directing the light into the tank.

http://i165.photobucket.com/albums/u...9/63c9b8cf.jpg

Shiny Shiny lol

http://i165.photobucket.com/albums/u...9/f2de2dcb.jpg

And the Canopy with Doors:

http://i165.photobucket.com/albums/u...ps809166ed.jpg

FishyFishy! 04-12-2013 09:38 PM

My god thats some amazing wood working skills you got there!!!! Beautiful!

Wanna come finish my stand??

Coralgurl 04-12-2013 10:11 PM

:jaw:Wow, that's beautiful woodwork!!! Looks like you've got the canopy on a tank, so let's see some more!!!

Thanks for sharing!

hillegom 04-12-2013 10:51 PM

I love the woodwork!
Great Job

LoJack 04-12-2013 11:15 PM

Quote:

Originally Posted by Coralgurl (Post 811136)
:jaw:Wow, that's beautiful woodwork!!! Looks like you've got the canopy on a tank, so let's see some more!!!

Thanks for sharing!

Alrighty ... Carrying on

The next step I took care of was soldering up my DIY LED's.

I purchased 3 heat sinks, and made 3 separate units. Each unit contained 12 Royal Blue (460nm) and 12 Cool Whites (6500K) wired into meanwell drivers controlled by RapidLED's dimmable controller.

http://i165.photobucket.com/albums/u...9/460badb7.jpg

http://i165.photobucket.com/albums/u...9/889aca92.jpg

White Test:

http://i165.photobucket.com/albums/u...9/6f8c8be1.jpg

Blue Test:

http://i165.photobucket.com/albums/u...9/22603889.jpg

They work! Time to mount

Oh wait ... pure Chaos!!

http://i165.photobucket.com/albums/u...9/7757b781.jpg

Chaos Cleaned up

http://i165.photobucket.com/albums/u...9/658f7cca.jpg

You can see that the right side is whiter than the left side. This meant that I needed to adjust the SVR2 setting on the driver for the blues on the left pendant which was taking slightly more amperage than the others.

A close up of a single heat sink

http://i165.photobucket.com/albums/u...9/56a167de.jpg

LoJack 04-12-2013 11:26 PM

Time to move back one step ... because the canopy was built after I had the plumbing done ... but it screwed up my sequence for the Journal.

So lets get to the plumbing.

First the tank needed to be drilled.

Plumbers putty and a bit of patience to the rescue:

http://i165.photobucket.com/albums/u...9/c8fc95a6.jpg

And thanks to trickery of photography ... I'm done

http://i165.photobucket.com/albums/u...9/768a8e70.jpg

http://i165.photobucket.com/albums/u...9/799a1b33.jpg

After the holes were drilled I painted the back ...

http://i165.photobucket.com/albums/u...9/6d2b9c07.jpg

And then began construction on the Coast to Coast Overflow

http://i165.photobucket.com/albums/u...9/373d443c.jpg

And voila!

http://i165.photobucket.com/albums/u...9/bab87001.jpg

The pump is a Reeflo Dart (3600 GPH)

http://i165.photobucket.com/albums/u...9/3cae034e.jpg

http://i165.photobucket.com/albums/u...9/46fcb619.jpg

http://i165.photobucket.com/albums/u...9/308222ca.jpg

And because I used the Beananimal overflow ... 3 standpipes

http://i165.photobucket.com/albums/u...9/78bf31ed.jpg

There is also a 1" line that diverts from my 1.5" piping on the return that circulates back into the sump. This is for a filter sock. But because my overflow doesn't go to the sock, there is a 0% chance of an overflow because of a plugged filter sock.

http://i165.photobucket.com/albums/u...9/a82dd8f1.jpg

The return on the pump is diverted into 4 separate outlets of loc-line that have fan nozzles and locline ball valves. This gives me full control in terms of flow. If I have a piece that can't handle the high flow, I can turn down 1 of the ball valves decreasing the flow in one area and increasing it in another.

http://i165.photobucket.com/albums/u...9/d904744e.jpg

http://i165.photobucket.com/albums/u...9/f95e41f8.jpg

Skimmerking 04-13-2013 02:47 AM

nice bro looking really good. where is the fans for the heat sink

LoJack 04-13-2013 04:00 PM

Quote:

Originally Posted by FishyFishy! (Post 811125)
My god thats some amazing wood working skills you got there!!!! Beautiful!

Wanna come finish my stand??

lol thanks ... Its a bit far to travel I think ...

Quote:

Originally Posted by hillegom (Post 811168)
I love the woodwork!
Great Job

Thank You very much. This was the first job of this calibre that I attempted. I couldn't find plans, so I just searched DIY stands on ReefCentral and got my inspiration from there ...

Quote:

Originally Posted by Skimmer King (Post 811249)
nice bro looking really good. where is the fans for the heat sink

I didn't put fans directly on the heat sink, they are exchanging the air in the canopy. 2 pushing fresh air in, 2 sucking warm air out.

daplatapus 04-13-2013 04:29 PM

Very nice work. Hope you don't mind, but I copied a couple of your corner post pics. I saw something similar on a reefcentral post a while back but couldn't find it again. I'll save it for posterity :)

An idea I saw (I can't remember where) for hanging heatsinks is run them on pocket door track. That way when you have to work in your tank you can just push them back on the rail and they're not hanging in your way. Just a though if you hadn't seen it done.


All times are GMT. The time now is 01:59 AM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.