RyanGSP's 80G Build
 

I picked this tank up today in Calgary, I figure it about 80G. The tank is 48.5"L x 22"D x 17"H with a left corner overflow, 1.5" drain and a 1" return. I am still unsure on equipment, I would like to go MH or LED for lighting, tunze 1262 return pump, and I am not sure about dual MP10W ES or MP40W ES. I think for the money spent I will see better results with the 10's but for right now its going to be pieced together slowly.

Here is how it looked after Mike & I got it in the house.
http://i53.photobucket.com/albums/g7...ld/photo26.jpg
http://i53.photobucket.com/albums/g7...ld/photo27.jpg


I wasted no time in cleaning this thing up.
Step One take off paint on sides.
http://i53.photobucket.com/albums/g7...ld/photo28.jpg
http://i53.photobucket.com/albums/g7...ild/photo3.jpg


Step Two take off the substrate stuck on the bottom
http://i53.photobucket.com/albums/g7...ld/photo29.jpg


And here is how it looks after a quick wipe down.
http://i53.photobucket.com/albums/g7...ild/photo2.jpg

Only one piece left to be scraped. The back only took about an hour but I found a technique half way through and the last half went pretty fast.

http://i53.photobucket.com/albums/g7...ld/photo30.jpg

http://i53.photobucket.com/albums/g7...uild/photo.jpg

Well after a trip to Home Depot, an agonizing weight at the till because they thought I was lieing how many pieces of lumber there was and the guy in that section on break here is the raw product.

http://i53.photobucket.com/albums/g7...d/photo2-2.jpg



Piecing it together.
http://i53.photobucket.com/albums/g7...ild/photo8.jpg

http://i53.photobucket.com/albums/g7...ild/photo7.jpg

http://i53.photobucket.com/albums/g7...ild/photo6.jpg


All finished
http://i53.photobucket.com/albums/g7...ild/photo5.jpg


http://i53.photobucket.com/albums/g7...d/photo2-1.jpg


On the stand
http://i53.photobucket.com/albums/g7...ild/photo4.jpg


Painting the back
http://i53.photobucket.com/albums/g7...d/photo3-1.jpg

http://i53.photobucket.com/albums/g7...ild/photo9.jpg

Thanks guys. I went back to the dark side tonight as well. Sorry Larry!

http://i53.photobucket.com/albums/g7...d/photo3-2.jpg

Well not much going on today. Secured the power bar to the stand and..... plugged it in.


http://i53.photobucket.com/albums/g7...ld/photo-1.jpg



Oh and I ordered glass for the euro-brace. After some consultation from Mike and the guys on canreef I got a pretty good idea on how I am going to do my canopy. BTW anyone got a source on some cheap quiet fans that plug into the wall?

Well I think I got a design for my sump, I think I will go 36" x 18" x 18". Tell me what you think.
http://i53.photobucket.com/albums/g7...ld/photo-2.jpg


Going from left to right the horizontal line is for a holder for my filter sock.
Below is a chamber for my protien skimmer and whatever else I want to put in there (reactors, probes etc.)
Next is a frag chamber; this will have a section in the back for mangroves. I am probably going to put in a rack for the mangroves and DIY a tray for substrate. Im still unsure if I want to permanently put in a trough for a DSB for the mangroves. This will mean the frag chamber is 12x12.
After that is a set of baffles then the last chamber is a section for the pump and the heaters.

BTW each square equals 1".

Another Update!!

Yesterday I got a Quiet One 4000 in next to new condition. I guess it was too big for the previous tank. Thanks again Randy!!


Today I spent my lunch hour running around like a chicken with my head cut off looking for plumbing supplies. I think I got all the fittings I need, all thats let is the loc-line so an order from J&L will happen here pretty quick.

I also was able to get my glass cut for my euro brace and blocks for the stand to sit on. Big thanks to Scott for grabbing that for me on his way home.

So here is everything when I got home.
Plumbing
http://i53.photobucket.com/albums/g7...d/photo2-3.jpg

Glass for the Euro Brace
http://i53.photobucket.com/albums/g7...ld/photo-3.jpg


Well apparently I got the glass for the sides too big so I put the glass master to work trimming off a 1/4 inch.
http://i53.photobucket.com/albums/g7...d/photo3-3.jpg


After a trip to TFI for a tube of silicone and a silicone gun, here I am putting down the silicone.
http://i53.photobucket.com/albums/g7...ld/photo10.jpg

This is what happens when you let the glass Master help you put on the euro brace.
http://i53.photobucket.com/albums/g7...d/photo7-1.jpg


Ofcourse the silicone was on the tank already so he sped off to TFI to get another brace cut and get the blocks for the stand cut.
http://i53.photobucket.com/albums/g7...d/photo9-1.jpg


Add 2 beads of silicone
http://i53.photobucket.com/albums/g7...d/photo5-1.jpg


Press onto Euro brace and you have a block that will keep my canopy frame off the bracing and water so it wont get wet.
http://i53.photobucket.com/albums/g7...d/photo8-1.jpg


The almost finished product. I am going to trim the excess silicone tomorrow evening.
http://i53.photobucket.com/albums/g7...d/photo6-1.jpg


I havent tried the plumbing yet but the night is young :D

Got most of the plumbing inside the tank done. All thats needed now is the Loc-Line and to construct the air control on the cap of the Durso.

http://i53.photobucket.com/albums/g7...d/photo3-4.jpg

Alright well another bunch of updates but where to start?

I got the overflow grate installed and they turned out alright. Im happy with them but I found my 1st mistake. I build the return line to clear the glass part of the overflow without taking into consideration the overflow grate. Ofcourse its glued already so I had to build a new one. DOH!
http://i53.photobucket.com/albums/g7...ld/photo-4.jpg

http://i53.photobucket.com/albums/g7...d/photo2-5.jpg



Next I found a take I can use as a sump. So yesterday I went out and got all the glass I needed to make the baffles. Unfortunatly I forgot to take a picture of the tank before I ripped the bracing off.
http://i53.photobucket.com/albums/g7...d/photo2-6.jpg

http://i53.photobucket.com/albums/g7...d/photo6-2.jpg

http://i53.photobucket.com/albums/g7...d/photo5-2.jpg

http://i53.photobucket.com/albums/g7...d/photo9-2.jpg

Now that the tank is all cleaned up its time to put in the glass.
This will be the shelf my sock holder will sit on.
http://i53.photobucket.com/albums/g7...d/photo7-2.jpg

Wall for the frag section and the beginning of the baffles
http://i53.photobucket.com/albums/g7...d/photo2-7.jpg

The completed Sump
http://i53.photobucket.com/albums/g7...d/photo4-2.jpg

Now to cut the hole in the shelf for the filter sock
http://i53.photobucket.com/albums/g7...ld/photo-5.jpg

I also got the lumber for the canopy.
http://i53.photobucket.com/albums/g7...d/photo8-2.jpg

I think I built it a little tall. The Its only 18" high but I think I should have gone 14-16 high.
http://i53.photobucket.com/albums/g7...d/photo3-6.jpg


Next weekend I want to skirt in the stand and canopy with some nicer wood. I plan on staining it dark to match the furniture. Hopfully lastlight will chime in here on this one.

I want to use his idea for the stand doors so they slide open. I would like to do the same with the canopy doors as well. What did you use to do this?