Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Reef (http://www.canreef.com/vbulletin/forumdisplay.php?f=8)
-   -   Vertex 180 Skimmer - Noisy again (http://www.canreef.com/vbulletin/showthread.php?t=54199)

newreefer_59 07-09-2009 03:36 PM

Vertex 180 Skimmer - Noisy again
 
Bought a Vertex 180 Skimmer in February and before long it seemed to get noisier than upon initial set up. Called the supplier about 2 months ago and they immediately sent out a new impeller shaft that was an upgrade. It seemed to do the trick, but the last few days the unit seems to be as noisy as it was before the replacement. Do I need to clean the shaft and motor unit every month or so, and is that the cause of the higher-than-expected running noise level?

fkshiu 07-09-2009 04:20 PM

I don't think there's much you can do. It's one of the compromises of the cheap Resun pump. You can't expect the world for what that skimmer sells for. Part of what you pay for with a BK, for example, is the silence.

albert_dao 07-09-2009 08:35 PM

Pull out the impeller and take a snap of the shaft if you could, especially the ends.

StirCrazy 07-09-2009 11:50 PM

cleaning the pump once a month wouldn't hurt either, I used to do all my pumps once aq month and they did get louder if I left them for a while longer.

Steve

newreefer_59 07-10-2009 04:43 AM

Attached is a pic of new and old impeller units
 
Impeller at bottom of pic is the newer one. They look identical at a glance. In any case, the unit does not appear dirty or anything, but still sounds louder than the first month......hey, perhaps it's just me but has anyone else noticed this?

freezetyle 07-10-2009 05:03 AM

i have a vertex in-100 and i find it quite loud. from what i hear its the resun pump. i like the skimmer just not the noise

Bryan 07-10-2009 05:27 AM

It a known problem with the Vertex, there was a bad batch of impellers. If you pull off the shaft from the impeller you will see wear marks on the shaft and the bore of the impeller will be ovaled out, this causes the impeller to vibrate. Replacing the shaft with a worn impeller does not help as it wills still vibrate. Contact the mfg, they will give you a new impeller. I have the ph number around here, the distributer is in Richmond, B.C.

albert_dao 07-10-2009 07:06 AM

Quote:

Originally Posted by newreefer_59 (Post 433897)
Impeller at bottom of pic is the newer one. They look identical at a glance. In any case, the unit does not appear dirty or anything, but still sounds louder than the first month......hey, perhaps it's just me but has anyone else noticed this?

Can you get a closeup of the end of the shaft? I need to see the edges of the shaft.

lastlight 07-10-2009 08:24 AM

Quote:

Originally Posted by albert_dao (Post 433931)
Can you get a closeup of the end of the shaft? I need to see the edges of the shaft.

Not the first time he's said that. Proof that Albert's always on the ball...always offering support through lip-service.

albert_dao 07-10-2009 08:34 AM

... I do not have a PG rebuttal to this.


All times are GMT. The time now is 08:18 AM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.