Canreef Aquatics Bulletin Board

Canreef Aquatics Bulletin Board (http://www.canreef.com/vbulletin/index.php)
-   Polls (http://www.canreef.com/vbulletin/forumdisplay.php?f=34)
-   -   Tunze or vortech pump (http://www.canreef.com/vbulletin/showthread.php?t=44027)

gordypoo 08-10-2008 01:56 AM

Tunze or vortech pump
 
Which one are you using and would perform better with the different settings?

Stones 08-10-2008 05:13 AM

I'm running two vortechs in my 90 gallon sps reef and love them. That is when they are actually running. Lets just say the nylon drive shafts don't get along too well with sugar sand.... I've had to order replacement parts for them several times in the 2 years that I've owned them which is my only complaint I would have.

I just upgraded them to all Gen 2 parts and already I've noticed they run quiter and will hopefully outlast their gen 1 predecessors. The options available for random circulation or wave generation are truly amazing. Now with the gen 2 programming, they have added even more wave modes, as well as a night mode. Plus, they take up relatively very little space in the tank and add no heat. That said, they can be a bit of a PITA to align and need to be cleaned more often than a tunze in order to run hassle free.

gordypoo 08-10-2008 07:50 AM

Ok not knowing a lot about these pumps is the new and improved model which it states on the J&L website include the Gen 2 upgrade. Does it inculude the MP40 watt? Little confused thanks.

Stones 08-10-2008 01:58 PM

I believe the "new & improved" vortech pumps being sold should have the gen 2 magnet, drive shaft, and wave driver programming. I'd be sure to check with the retailer prior to ordering just to be sure. If it is not the gen 2, you have to find someone locally to flash your wave driver to upgrade its firmware, or you have to send it in to ecotech which will set you back ~$50 canadian for shipping to and from here. The gen 2 magnet, drive shaft, and wet frame back kit costs $9.85 directly from ecotech and shipping is cheap if you are just shipping replacement parts.

fkshiu 08-10-2008 04:39 PM

I love my Tunzes, but I don't think you can go wrong with either the fixed gen2 vortechs or tunzes. It's more a matter of style.

You can aim tunzes (almost anywhere with the Stream 2s coming out), but not vortechs.

Vortechs are lower profile than tunzes.

rockworm 08-10-2008 05:39 PM

I use the Tunze 6101's and 6055's. If you plan on using a controller, these integrate perfectly into the Profilux and you don not need the Tunze controller.

As said though, you cannot go wrong with either.

jpdutton 08-10-2008 06:07 PM

I'm using two 6101 tunze connected to my Profilux, I have the decor rocks for both of them so I get wicked flow and you can't see them.

I was thinking of swapping them out for the 6055s becuase I've moved down from a 120g to a 75gcube.

kwirky 08-11-2008 08:24 PM

I'm using a Vortech MP40W on my 45g tank. I think if you go with vortechs u need one for every 60g to get the most benefits. Tunze's are better for large tanks I think (200g plus or 8' and longer). The vortech doesn't have much strength 3' away from the powerhead in the water.

DanG 08-12-2008 12:31 AM

I ordered a vortech from J&L a couple weeks ago and emailed to confirm they're all version 2 and Jeff from J&L confirmed they are.

gordypoo 08-12-2008 02:13 AM

Thanks for your opinions and info on the pump. My tank is only a 72 gallon and from what i have read and seen in video i am sure it will be more than sufficient. I had a hydor 4 which just died for some silly reason after 7 months so instead of replacing it i will invest in a better pump.


All times are GMT. The time now is 01:49 AM.

Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.